Single phase loads can go as high as the connected device requires. Of course the higher you go with the load , so goes the equipment to support it. Larger wires sizes, breakers etc..
Answer for UK, Europe and countries running a 50 Hz supply service.Common single phase meters for a 240 v system can take a 60 amp or sometimes a 100 amp load for domestic use.
Impossible to say without more details. It depends entirely on the voltage of the supply and whether it's single-phase or three-phase.
..the questions does not say wether the 30kVA transformer is 3 phase transformer or single phase transformer..but it is implying that a single phase welding load at 16A per phase is to be connect to it, it is assumed then that the transformer is 3 phase transformer..we assume load is rated 240V.. ..though not much details is given about the transformer voltage specs. but if is rated 3 phase 415/240V, the approx full load current per phase is given by 30KVAx1.3912=41.736A.. ..but if the transformer was rated single phase 240V say, the approx full load current FLC=30000/240V gives 125ampers.. ..if you further devide the FLC by the intended load current.. ..Recommended no of welders per for a 3 phase 415V transformer and assuming single welding sets =41.736/16=2.6..so you can connect max two welding sets to this transformer per phase,..max 6 weld sets can connect at an approx load factor of 76%.. ..for the single phase transformer, FLC/16=125/16, gives 7.8 but is also recommended not to connect more than 6 welding sets to such transformer for the same reasons..
How much current equipments are drawing from three phases (combined or individual) is called three phase load and how much supply we are getting from source is called three phase supply. Ex. In INDIA single phase supply is 220 volt ac with neutral. So in three phase supply all RYB phases should be 220 volts ac with neutral individually. If we calculate with phase to phase than it shoulb be 415 volts ac.
To calculate the amperage, use the formula: Amps = Watts / Volts. For a 3000-watt load on a 220-volt AC single-phase circuit, the amperage would be approximately 13.6 amps.
- For a single phase supply @ 220 voltscurrent drawn by 5kva UPS = 22.7 amperes (at full load.)
I dont know if you can actually convert the oven's wiring from 3-phase to single phase. You can, however, convert the single phase circuit that will feed the oven to a 3-phase system. To this you will need a phase converter. Now, where to purchase such an item, and how much they cost? i have no idea.
In three phase: I = (three phase VA) / (sqrt(3) x (phase to phase voltage)) for single phase: I = (single phase VA) / ((phase to neutral voltage)) keep in mine three phase VA = 3 x (single phase VA), and phase to phase voltage = 1.732 x (phase to neutral voltage) Therefore the single phase and three phase currents are the same (ie, the three phase currents are the same in all three phases, or balanced). But don't get available current and available power confused (KVA is not the same as KW).
A 3 phase system needs only to use 3 or 4 conductors, as against 6 conductors if it were 3, single phase conductors The amount of copper used in a 3 phase is much less than what would be needed in a single phase system carrying the same current, this reduction in copper allows for weight reduction and cost savings. The power losses in a 3 phase system are much less than in a single phase system.
For 1 hp motor, a single phase starter is used. Because a single phase starter gives economy consumption,easy trouble shooting and easy installation when compared to three phase starters and supply....
For those who need a three-phase supply, they are essential. If a single-phase supply is needed, a three-phase generator is uneconomic. Three-phase is used for loads of more than about 15-20 kVA.
Probably not. The single phase three horse power motor will be much larger in physical size than its three phase counterpart, and will probably not fit.