0
How much voltage is required to run 0.42 A of current through a 15 ohm resistor?
Wiki User
∙ 6y ago
Use Ohm's law:
U= R x I = 3 Ohm x 6 amps = 18 Volts
Thus you need 18 Volts to supply such a load.
Wiki User
∙ 13y ago
Wiki User
∙ 6y ago6.3 V
Add your answer:
Earn +20 pts
What is the current through the 150 ohm resistor?
It depends on the voltage applied across it. But the maximum current is limited by the power-rating of the resistor (power divided by the square of the voltage).
What size of resistor is required to operate the LED from a 9V battery?
In order to determine what size of resistor is required to operate an LED from a 9V battery, first start by knowing the current and voltage required for the LED. That information is available in the LED's specifications. For discussion purposes, lets assume a typical LED at 2.5V and 50mW. The translates to a forward current of 20mA. Build a simple series circuit containing a 9V battery, a resistor of an as yet unknown value, and the LED. By Kirchoff's current law, the current in the LED is the same as the current in the resistor, which is also the same as the current in the battery. This is 20ma. By Kirchoff's voltage law, the voltage across the LED plus the voltage across the resistor equals the voltage across the battery. This is 6.5V. (9 - 2.5) By Ohm's law, resistance is voltage divided by current, so the resistor is 6.5 / 0.02, or 325 Ohms. The nearest standard value to that is 330 Ohms. Cross check the power through the resistor. Power is voltage times current, or 6.5V times 0.02A, or 0.13W. A half watt resistor is more than adequate for this job.
If voltage constant when the current increases what does the resistance do?
In an electric circuit, ratio of current and voltage is constant which is known as the resistance of the circuit. If voltage or current is to be changed the resistance has to be changed. You cannot keep an invariable resistance in the circuit and increase current while keeping voltage as constant.Hence to vary the voltage or current in a circuit different equipments like rheostat,potentiometer are used.
How does an ammeter work?
An ammeter is a low voltage voltmeter in parallel with a small resistance resistor. Current flow through the resistor creates a voltage drop across it which is then measured by the voltmeter.
How did the current before the resistor compare with the current after?
Current flow would be the same through the resistor, since it's in series, but the voltage would be slightly reduced based on the resistance. If you have 2 resistors in parallel, the current will divide through each resistor, and the voltage stays the same. PLL Ohm's law and water flow - PLL
Does voltage flow across or through a resistor?
No. If a voltage is applied across a resistor, a current flows through it.
Is current is drop when it flowing through the resistor?
Current flows in loops, voltage drops across elements. With relation to current, what flows in, must flow out, so no, current is not dropped across a resistor, it flows through a resistor and voltage is dropped across the resistor.
What is the current drop across the resistor?
The correct question is what is the voltage drop across a resistor or the current flowing through the resistor using Ohm's Law where Voltage = Current x Resistance
What is the use of resistor in the circuit?
A resistor develops a voltage differential when current is passed through it. Ohm's law: Voltage is current times resistance.
Does current flow through a resistor or across a resistor?
Normally through the resistor's internal construction. It flows through any part of the resistor that has low resistance- be it anywere. And then there's this. It might be that one should consider that current flows through a resistor and voltage is dropped across a resistor. Perhaps this is where the question began. The former is fairly straight forward. The latter can be vexing. Voltage is said to be dropped across a resistor when current is flowing through it. The voltage drop may be also considered as the voltage measureable across that resistor or the voltage "felt" by that resistor. It's as if that resistor was in a circuit by itself and hooked up to a battery of that equivalent voltage.
What is the voltage drop across a resistor of 300 kilo ohm?
What is the amount of current flowing through the resistor? Voltage drop is dependent on the current. Ohm x Amps = Voltage drop
What is the rule for voltage across each resistor?
Volt across a resistor = resistance x current through the resistor.
How much voltage is required to run 0.64 A of current through a 240 resistor Use V IR.?
2.7 x 10^-3
What is the current through the 150 ohm resistor?
It depends on the voltage applied across it. But the maximum current is limited by the power-rating of the resistor (power divided by the square of the voltage).
Does a resister use current?
It may be better to say that a resistor allows current flow through itself rather than to say that a resistor is a device that will "use" current. It does "resist" current flow, and thus limits it to some degree depending on its resistance. (More resistance means more limiting of current flow.) The resistor "drops voltage" as well limits current. A resistor "feels voltage" from some source, and the voltage it "feels" is said to be the "voltage drop" of the resistor. The voltage drop is the voltage that could be measured across that resistor with a meter.
When the current traveling through a resistor is increased what happens to the voltage that travels through the same resistor?
Your question reveals fundamental misunderstandings about the nature of electricity.'Voltage' is simply another word for 'potential difference', and a potential difference appears across opposite ends of the resistor; it doesn't 'travel through' that resistor! Current, on the other hand, DOES 'travel through' the resistor and is caused by the potential difference across the resistor.Resistance is the ratio of potential difference to current. So if the resistance remians unchanged when the current through it doubles, then it has happened because the potential difference has doubled.
What kind of relationship can be concluded about the voltage difference across a resistor and the current flowing through it?
POWER=VI. V=voltage I= current
