0
Ballast connection diagrams are on the identification label that is on the ballast.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do I wire a 220v ballast when it has only 1 wire labeled 220 when I have 2 wires coming off of my double leg breaker?
Your ballast should show two wires for supply side of ballast. Make sure that neither side of this is grounded to the light and connect the 220 V from your breaker to these two wires and then connect a ground to the chassis of the light from the panel.
Will a higher wattage hps bulb work in a ballast that came with a lower wattage bulb?
A higher wattage HPS bulb may work with a ballast that is rated for a lower wattage bulb , but may appear to be dim and will not produce the rated light output. It is best to match ballast and bulb accordingly.
How do you wire a 4-lamp electronic ballast?
The way a metal halide light is set up, there's a transformer in it called a "ballast." The ballast powers the bulb. You can wire ballasts to a lot of different voltages--which voltages you can use are dependent on the ballast in question--but 120v single phase is almost always one of the choices. So yes, you can do it.
How many amps fluorescent bulb?
When you buy the bulb. All of those specifications should be on the package. To figure the Kilowatts it's pulling and cost to run. kW = amps x volts / 1000. then just take your kW x price per kw. and that will give you how much it costs to run that bulb for one hour. The amperage is on the label of the ballast. When you connect the ballast to power you will see it along with the voltage and pf of the ballast. F40T12 twin 8 foot tubes, ballast usually draws about .75 amps.
Can T8 LED tube light be used with ballast and can ballast be removed and will it work?
A T8 LED tube has to be used with a ballast to bring the correct voltage to the tube for it to operate correctly. Removing the ballast from the circuit will prevent the tube from operating.
How can 5 fluorescent lights be connected together?
Connect them in parallel. The black wire from the ballast to the black line wire. The white wire from the ballast to the line neutral. Connect the ground wire to the ground screw which is located in the body of the fixture. Grounding of the fixtures is essential.
How do I wire a 220v ballast when it has only 1 wire labeled 220 when I have 2 wires coming off of my double leg breaker?
Your ballast should show two wires for supply side of ballast. Make sure that neither side of this is grounded to the light and connect the 220 V from your breaker to these two wires and then connect a ground to the chassis of the light from the panel.
How do you connect 250 watt bulb into a ballast?
If the 250 watt bulb is a HID or similar type the ballast comes complete with the fixture. The bulb socket is also part of the fixture and comes pre-wired to the socket. To connect the bulb to the fixture all that has to be done is just screw it into the fixture's socket.
Where is the ballast resistor on a 2000 Chrysler Sebring convertible?
It does not have a ballast resistor.It does not have a ballast resistor.
Where is the ballast resistor for a 1994 Jeep Cherokee?
It does not have an ignition ballast resistor.It does not have an ignition ballast resistor.
How do you wire 120 volt 2 bulb 8 ft?
It sounds like you are talking about a two tube eight foot fluorescent fixture. Open the fixture up and you will find a ballast that has probably two yellow wires, two blue wires, two red wires and a black and white wire coming out of it. The 120 volt supply will connect to the black and white wires that protrude out of the ballast. Black ballast to black supply and white ballast to white supply.
Will a higher wattage hps bulb work in a ballast that came with a lower wattage bulb?
A higher wattage HPS bulb may work with a ballast that is rated for a lower wattage bulb , but may appear to be dim and will not produce the rated light output. It is best to match ballast and bulb accordingly.
Ballast smells burnt what to do?
A ballast that smells burnt is going bad. The ballast will have to be replaced to fix the problem.
How do you wire a 4-lamp electronic ballast?
The way a metal halide light is set up, there's a transformer in it called a "ballast." The ballast powers the bulb. You can wire ballasts to a lot of different voltages--which voltages you can use are dependent on the ballast in question--but 120v single phase is almost always one of the choices. So yes, you can do it.
What is a good sentence for the word ballast?
A good sentence for the word ballast is.......The ballast is not heavy enough and the boat is about to sink.
How much does a David Brown 880 diesel tractor weigh?
Static weight with opperator -Rear 5430 lb with ballast 2950 lbs without ballast --------------------------------------Front 1810 lb with ballast 1540 lbs without ballast --------------------------------------Total 7240 lb with ballast 4470 lbs without ballast ----
What is Ballast Nedam's population?
Ballast Nedam's population is 2,009.
