0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Where is fuel fuse in Hyundai excel 1990?
fuse box in the engine bay
How big is the petrol tank of a 1993 Hyundai Excel GS?
45 Litres.
Where is the ignition module located on a 1993 Hyundai Excel?
The 1993 Hyundai ignition module is located on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.
Why do you have to pull out the choke on morning to start your 1993 Hyundai excel?
To make the engine run richer
Head bolt torque settings for Hyundai Excel 1993?
torque settings are 35-60-73
How do you remove the rear bumper cover on a 1993 Ford Taurus wagon?
To remove the rear bumper cover on a 1993 Ford Taurus wagon, the lights need to be disconnected in the rear. Once all electrical connections are disconnected in the rear, remove the taillights and the fuel filler overflow hose. Remove any nuts and bolts holding the bumper cover on. Using needle nose pliers, pop the push pins around the bumper cover upwards. Slowly pull on the bumper to remove it.
Where is the flasher fuse for 1993 Hyundai Excel?
Fuse box inside car at left front kick panel (by your left foot) Fuse #17---10amps
How do you replace the headlight assembly located on a 1993 Acura Integra?
First, you'll need to remove the front bumper. To do this, take off the bolts underneath the front part of the bumper. Remove the bumper turn signals to access the two bolts per side that hold the bumper on the car. Support the bumper by putting something underneath it. Then get a stubby Phillips screwdriver and remove the two screws per side at the end of the bumper (in the wheel well). Bumper should come off. Remove the headlight assembly by diconnecting the headlight sockets, remove the 10mm bolts above each headlight assembly. Remove the 10mm bolts below the headlight assembly. Done.
How do I remove a rusty old 1993 Ford f 250 front bumper and replace witha new one?
Spray some PB Blaster on the rusted bolts. Remove bolts and take bumper off. Install new bumper and new bolts. Used anti-seize on the bolts.
How do you replace a front bumper for a Maxima 1993?
* Apply the parking brake raise the vehicle and support it securely on jackstands * Disconnect the negative battery cable and disconnect any wiring that would interfere with bumper removal * From below remove the splash panel below the radiator and bumper * Remove the radiator grille and remove the headlight housings,turn signal lamps and cornering lamps * Remove the headlights and cornering lamps and remove the fasica to fender fasteners then remove the remaining fasteners and the bumper cover taking care to avoid damaging the cover and the fenders * Working under the vehicle remove the bumper beam mounting bolts Note:The bumper beam brackets can be removed from the chassis by removing the nuts from the studs at the back of the bracket or removing the foam inserts to access the front mounting bolts once the bumper cover is removed * Detach the bumper assembly from the vehicle
How do you replace the rear bumper on a 1993 Saturn?
Open the trunk. Remove all the pushpin retainers. Look under the rear fenders.. remove any screws and pushpin retainers. Remove the braces, if any. Look under the bumper cover itself and remove any pushpins. When all these fasteners are removed, the bumper cover should just slide off. If you want to replace the whole bumper (metal and styrofoam included), take it to a pro or grab a service manual.
How do you remove and replace the rear bumper of a 1993 Ford Escort LX?
I believe you have to remove the splash guards inside the wheel well. but as for finding a new bumper, I don't know. I found one place online that sells the bumper for the sedan model, but I have the LX, and I think I'm just going to have to find one in a junkyard somewhere.
