0
use of routerrip command
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What router prompt can you use the router rip command?
On a cisco router you would go into privilege-exec mode (enable) and then into "configure terminal" mode. From there you can use the router rip command.
Which command or set of commands will stop the RIP routing process?
no router rip
Which two statements are true about the use of the debug ip rip command on a Cisco router?
The debug ip rip command displays RIP routing activity in real time. The debug ip rip command can be issued at the user EXEC configuration mode.
Which of the following would be the correct command sequence to enable RIP on Router B for all connected networks?
RouterB(config)# router rip
Which command enables rip on a router?
A(config)# router rip A(config-router)# passive-interface S0/0 B(config)# router rip B(config-router)# network 192.168.25.48 B(config-router)# network 192.168.25.64 A(config)# router rip A(config-router)# no network 192.168.25.32 B(config)# router rip B(config-router)# passive-interface S0/0 A(config)# no router rip
What comment are use to delete a routing protocols in cisco router?
No router eigrp <AS #> No router ospf <process ID> No router bgp <AS #> No router rip
Which command is used to view the RIP routing protocol settings and configuration?
you can use SHOW IP PROTOCOL you will be able to see all running protocols in your router and its details...
What command is used to stop rip routing updates from exiting out an interface but still allow the interface to receive rip route updates?
Router(config-if)#no routing
Implementing Distance-vector routing protocol?
First you must decide what specific protocol you want to use. Then you configure it on the individual routers. Example, with Cisco routers: Router(config)#router rip Router(config-router)#network 10.0.0.0. Router(config-router)#exit Additional commands may be required for optimization. Note: I use RIP for illustration purposes, but it is usually not the best option for routing.First you must decide what specific protocol you want to use. Then you configure it on the individual routers. Example, with Cisco routers: Router(config)#router rip Router(config-router)#network 10.0.0.0. Router(config-router)#exit Additional commands may be required for optimization. Note: I use RIP for illustration purposes, but it is usually not the best option for routing.First you must decide what specific protocol you want to use. Then you configure it on the individual routers. Example, with Cisco routers: Router(config)#router rip Router(config-router)#network 10.0.0.0. Router(config-router)#exit Additional commands may be required for optimization. Note: I use RIP for illustration purposes, but it is usually not the best option for routing.First you must decide what specific protocol you want to use. Then you configure it on the individual routers. Example, with Cisco routers: Router(config)#router rip Router(config-router)#network 10.0.0.0. Router(config-router)#exit Additional commands may be required for optimization. Note: I use RIP for illustration purposes, but it is usually not the best option for routing.
Which command will display RIP activity as it occurs on a router?
"debug ip rip" is the correct answer. Use to display information on selected RIP events. This command has many keywords that allow you to specify a variety of RIP events. You can set the level of severity for the events you want displayed; specify the desired descriptive term or a corresponding number (0-7). You can set the verbosity of the messages you want displayed: low, medium, high. Example host1#debug ip rip events Use the no version to cancel the display of any information on the designated variable.
How do you set default root in a router by using dynamic routing?
If the network uses the RIP protocol, router A will determine that all paths have equal cost. If the network uses the RIP protocol, router A will update only the A-C-E path in its routing table. If the network uses the EIGRP routing protocol, router A will determine that path A-D-E has the lowest cost. If both RIP and EIGRP protocols are configured on router A, the router will use the route information that is learned by the RIP routing protocol.
The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router what is true concerning this command?
The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC
