Want this question answered?
You cannot copy it your self you need a locksmith or the dealer to program it.
How do you program a an ignition key for 2008 Chevy truck
To program a new key for a 2006 Grand Prix, insert the key into the ignition and turn it to the 'on' position. Now you must wait 10 minutes 30 seconds. When the time is up, you have 45 seconds to turn the key back 'off.' Repeat this step two more times. When you turn it to the 'off' position for the third time, turn it back to 'on' and you're done.
You can program a blank key for Mitsubishi Endeavor 2006 using Transponder Key Blank Fits.
In order to program a key on a 2004 VW Passat, you need to first put the existing key in the ignition.
When you say program, do you mean make the ignition cylinder so you can insert the key and turn it to start the vehicle? If so you can bring it to a lock shop and have them program the key.
you have to take it to a dealer.cost about 150.00 they have to program key to the car.
you can program a key if you already have two known good keys. if not you will have to pay the dealer or a locksmith
1. Close the vehicle doors.2. Turn OFF the ignition.3. Remove the key from the ignition.4. Press and hold the driver side door lock switch in the UNLOCK position.5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).10. Perform the previous step to program up to four transmitters (including your old ones).11. Remove the ignition key in order to exit the Program Mode
How do you program a key fob to a 2003 Chevy Malibu
Should work 1999-2006 Pontiac Montana. To create spare key: 1) Place alread programmed key into ignition. Cycle ignition from OFF - ON(RUN) - OFF. 2) Within 15 seconds, insert the new transponder key in the ignition. 3) Turn the key to ON(RUN) or START. 4) The theft "Security" light will go on then off. Turn key to "OFF" position. 5) The key will now start the vehicle.
There's a manual method of programming keyless entry transmitters also. Make sure that you have all the transmitters you want to be able to use handy because the system will have to "learn" each one, even if they already worked before. If you have the memory seat/radio/mirror option you'll need to program the remote for 'There's a manual method of programming keyless entry transmitters also. Make sure that you have all the transmitters you want to be able to use handy because the system will have to "learn" each one, even if they already worked before. If you have the memory seat/radio/mirror option you'll need to program the remote for 'driver 1' first, then 'driver 2', then up to 2 others. Here's how to do it: 1. Close the vehicle doors. 2. Turn OFF the ignition. 3. Remove the ignition key from the ignition lock cylinder. 4. Press and hold the driver side door lock switch to the unlock position. 5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.) 6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.) 7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder. 8. Release the door lock switch. The body control module (BCM) will sound three beeps in order to verify the Program Mode has been activated. 9. Press the lock and unlock buttons on the keyless entry transmitter simultaneously for approximately 5 seconds . The BCM will sound two beeps in order to verify that the transmitter has been successfully programmed. 10. Perform the previous step to program up to four transmitters. 11. Remove the ignition key in order to exit the Program Mode. 12. Verify the proper operation of each transmitter.driver 1' first, then 'driver 2', then up to 2 others. Here's how to do it: 1. Close the vehicle doors. 2. Turn OFF the ignition. 3. Remove the ignition key from the ignition lock cylinder. 4. Press and hold the driver side door lock switch to the unlock position. 5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.) 6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.) 7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder. 8. Release the door lock switch. The body control module (BCM) will sound three beeps in order to verify the Program Mode has been activated. 9. Press the lock and unlock buttons on the keyless entry transmitter simultaneously for approximately 5 seconds . The BCM will sound two beeps in order to verify that the transmitter has been successfully programmed. 10. Perform the previous step to program up to four transmitters. 11. Remove the ignition key in order to exit the Program Mode. 12. Verify the proper operation of each transmitter.