Top Answer
User Avatar
Wiki User
Answered 2010-02-19 17:21:05

Sorry, you can't. Hopefully someone will invent that sooner or later!

User Avatar

Your Answer

Related Questions

Technically speaking, a Cingular phone can be used with T-Mobile, as you only need to switch the SIM card. However, the phone may be locked to Cingular, in which you need to unlock it to be used with another GSM network.

yes u have to drop your contract but then they fine you so much money for dropping your contract. ask cingular about it. yes u have to drop your contract but then they fine you so much money for dropping your contract. ask cingular about it.

npn is a better switch than the pnp.

If you want the Sprint phone number on the Cingular phone. You will call Cingular and ask to port in your number. If you port in your number the Sprint phone will be canceled after the port is complete. If you are still under contract with Sprint you will have an Early Termination Fee. So make sure you are out of contract before you do this unless you don't mind paying $150-$200 for an ETF. If you are just wanting to switch the phone and keep Sprint Service while using a Cingular device. That does not work. Sprint doesn't used Unlocked phones.

you can just use a toggle switch,,,you need a relay capable of the amps it takes for the would connect between the starter and the battery,then you would need a toggle switch preferably a momatary toggle switch to activate the relay.

I have a 9 two 5 and i love it. The 9two5 will definitively be more versatile then the switch. The switch wont be as carvy and will be better for dh.

In general a switch is better than a hub because it doesn't repeat signals to all of the ports (and thus reduces collisions).

No you cannot, but you can use it in an UNLOCKED T-Mobile phone. Cingular and T-Mobile work off the same network which is GSM and this allows you to switch phones. I have T-mobile but the phone I am using right now is an unlocked cingulart phone. Nextel/Sprint and Verizon work off of the CDMA network and this is why you cannot use it.

Preferably the time to use the switch is in DRY CONDITIONS with quarter mile straight aways or less and sharp cornering ti provide more stability to help stabilize steering.

A parallel circuit is better because if you want to switch on/off somewhere, you would only switch on/off that place only. In a series circuit, switching on/off somewhere would switch on/off everywhere!

There is no need of a video illustration for this simple work. Take the neuter wire from the switch box directly to the electrical equipment viz fan/light or any other gadget and connect firmly. Connect phase wire to one of (preferably lower) terminal of the switch.Connect another wire to the other terminal of the switch and lead this wire to the instrument preferably through the came channel/pie through which the neuter wire is drawn. The switch of the new connection can also be fixed at convenient place instead of the same switch box .Do not forget to switch off the main switch before doing all these or any other electrical work/maintenance work.

yes, transistors are better as they can switch between on and off states

A switch does not use wattage, or consume power which is a better way of putting it. It depends on what appliance is being controlled by the switch.

No, you can not use a Verizon provided phone on a Cingular network, unless it is an unlocked phone. Most of cell phones you get with service provider (e.g. Verizon) plans and deals are locked to that particular network and can not be used with another service provider's network unless you unlock the phone.AnswerAlso - Cingular (now AT&T) is a GSM carrier and Verizon Wireless is a CDMA carrier. Each uses different cell phone technology making them incompatable. You can use an AT&T phone and switch it to a go phone once your contract runs out or visa versa. Sometimes pay as you go phones are the best option.

A switch is better. A Hub sends and receives traffic on one channel, a Switch: each port carries its own traffic, in and out.

Your motor has died, or is simply not connected properly. It may also require a fluid refill, preferably automatic transmission fluid. It could also be the relay switch. You will need a new relay switch if that is the problem.

You can jump start an older vehicle like this by shorting out the starter and solenoid with a screwdriver being careful to use one that doesn't ground you. You must have the vehicle switch to on. If you cannot get the vehicle to switch on you can hotwire the wire to the distributor to the battery. Not the safest way but in an emergency. A better way is to get a remote starter switch and wire it to the starter per its instructions. This is not to be confused with one of the newer remote starters which must be patched into the vehicles ignition and fuse box. You can also wire an ignition switch, preferably with an inline fuse, to the starter as well. This is a DIYer so if you have no electrical/mechanical training or experience then I'd get someone to help you. Good luck.

a better way of fixing it is to find the wires going into the switch and just join them together thus bypassing the switch and the need the buy a new switch if that is the problem and the need to press the clutch at the same time

A "one way switch" or better known as a single pole switch is simply a device that breaks the electrical circuit to a device. ie; A single pole light switch is used to turn off and on lights from one location.

For more games and other capabilities you can buy the iPhone 7 or if you want a mobile console get the Nintendo Switch

A network switch handles traffic better than a hub, which is a bit of a dumb device. Each is good for different situations.

it simply divides your network into a smaller logical segments, due to have better performance, and better securty..

Copyright ยฉ 2021 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.