0
There is no 8 ohm solid state amp. Really! The output impedance of such an amp will be arround 0.4 ohms. Scroll down to related links and look at "Interconnection of two units- Voltage Bridging - Zout < Zin".
You can, as long as the amp's impedance is much lower to the speaker(s) total ohm load you're fine. We have never impedance matching there.
Wiki User
∙ 15y ago
Wiki User
∙ 14y agoSorry, but there is no 6 ohm amplifier on the market. The power amplifier has always an output impedance of 0.5 ohms or less. We don't use impedance matching, we use voltage bridging. Scroll down to related links and look at "Interconnection of two audio units - power amplifier and passive loudspeaker".
Wiki User
∙ 14y agoNo, you should not play 8 ohm speakers on a 16 ohm amp.
You can overload the amp and damage it. Also, the same power setting you are used to using will be four times the power with the 8 ohm speaker, and you can damage the speaker.
Wiki User
∙ 14y agoA1: The output impedance of a power amplifier is always less than 0.1 ohms. There are no 8 ohm amplifiers on the market!
A2: I actually just bought a new car radio/CD player that specifically shows 4 ohm speakers on the sticker. It is designed to work optimally with 4 ohm speakers. If you use 8 ohm instead, it will work, but you will not get the full power output that is specified. The amp can only kick out so much voltage and so much amperage - if it is designed for 4 ohm speakers, and 200 watts (stereo, so 100 watts per speaker), it can supply 20 volts (P = V^2 / R). If you used 8 ohm speakers to this amplifier, each speaker would only get 50 watts powered at full output voltage.
Alternatively, if it is designed for 8 ohm speakers and 100 watts per speaker, it can provide 40 volts. If you used 4 ohm speakers instead, each speaker could be given 200 watts at 40 volts, resulting in severe overheating and damage to the amplifier.
This applies to your case as well: it is OK to hook up higher impedance speakers to a lower impedance amplifier, but you will get less power delivered. If you do the opposite (lower impedance speakers to higher impedance amplifier), keep the volume low or you could burn out the amp.
Wiki User
∙ 13y agoYes, you can hook two 8 ohm speakers together in series for use with 16 ohm amplifier. Just make sure they are in phase, red dots not together or apart, so that you don't get phase cancellation.
Wiki User
∙ 12y agoYou should not do that. It will work, but you will not get rated power out of the configuration. You will probably only see one quarter of the rated power before the amplifier starts to clip on voltage. You also might damage the amplifier, because the voltage clip point will not be at the same point relative to the current clip point, causing an imbalance in the power drivers.
If you really wanted to do this, you could connect two 16 ohm speaker in parallel, presenting 8 ohms to the amplifier. The amplifier would then be happy, and the speakers would be loaded to only half power each. Just be sure to phase them correctly by connecting the red dotted terminals together.
Wiki User
∙ 10y agoThere is really no 8 ohm amplifier on the market. The power amplifier will have an output impedance of around 0.04 ohms.
Wiki User
∙ 15y agoredefine your question there is no 4 ohm amplifier. If you mean put a 16 ohms speaker into an amplifier designed to drive a 4 ohms speaker ? yes you can but the efficiency will not be there.
Wiki User
∙ 14y agoYes unless you always have the amp at full volume. If you do then you could put the two speakers in series and push the mono button.
Wiki User
∙ 12y agoYes, you can make 8 ohm speakers work on an amp requiring 16 ohm speakers, but you will need to use two 8 ohm speakers in series, so as to maintain the correct 16 ohm load.
Add your answer:
Earn +20 pts
Can you run 4ohm resistor to make 4 ohms speakers 2 ohm?
Yes, you can safely use a 4 ohm amp with one 8 ohm speaker, but you will not achieve full power. The 4 ohm amp is designed to supply a certain voltage into a 4 ohm speaker. Supplying that same voltage to an 8 ohm speaker will result in half the power, or -3dB. For maximum power, use a 4 ohm speaker, or two 8 ohm speakers in parallel.
What is better 16 ohms speakers or 8 ohms speakers?
It depends on the application. If you have an amp that is stable in 8 ohms per channel, then 8 ohm speakers will work best. However, if you wanted multiple speakers on that channel you could use two 16 ohm speakers.
Will wiring a 16 ohm woofer with a 16 ohm tweeter in parallel result in a total ohm load of 8 ohms?
If you mean as pairs, yes. put an 8 Ohm and a 16 Ohm speaker in parallel for each channel. The 16 Ohm speakers will take 1/3 the power and the 8 Ohm speakers will take 2/3 the power. The resulting impedance will be 5.33 Ohms.
Can you wire 2 16 ohm speakers to 16 ohms?
No. Two 16 ohm speakers connected together are either 32 ohms, if wired in series, or 8 ohms, if wired in parallel. You can, however, connect four 16 ohm speakers in series-parallel to get 16 ohms, with four times the power handling capacity of just one.
8 Ohm plus 8 Ohm equals?
16 Ohms. Yes 16 ohms in series. 4 ohms in parallel
Can you use a 6 ohm and a 16 ohm speakers with a 6 ohm amp?
No. Not and maintain good balance and dynamic range.
Can you put 4 ohms into 16?
Sure, If you mean your stereo has 4 ohm output and using 16 ohm speakers. The volume will be reduced somewhat by doing this, but it won't harm the stereo. If you have 4 ohm speakers and stereo is designed for 16 ohms you can do it ,but the amp will run hot and you may suffer damage at high volume to the amp.
Can you run 4ohm resistor to make 4 ohms speakers 2 ohm?
Yes, you can safely use a 4 ohm amp with one 8 ohm speaker, but you will not achieve full power. The 4 ohm amp is designed to supply a certain voltage into a 4 ohm speaker. Supplying that same voltage to an 8 ohm speaker will result in half the power, or -3dB. For maximum power, use a 4 ohm speaker, or two 8 ohm speakers in parallel.
What is better 16 ohms speakers or 8 ohms speakers?
It depends on the application. If you have an amp that is stable in 8 ohms per channel, then 8 ohm speakers will work best. However, if you wanted multiple speakers on that channel you could use two 16 ohm speakers.
Can an 8 ohm amp drive 16 ohm speakers?
Never heard of a 16 ohm hifi aplifier. All amplifiers have an output impedance of less than 0.1 ohm. We use always impedance matching with a low source impedance to the much higher load impedance. Scroll down to related links and read "Amplifier, Loudspeaker, and Ohms".
How do you use 16 ohm monitor speakers with an 8 ohm powered mixer?
Just use it like an 8 ohm speaker or else connect two 16 ohm speakers in parallel to form an 8 ohm load. Parallel is positive to positive and negative to negative.
Will wiring a 16 ohm woofer with a 16 ohm tweeter in parallel result in a total ohm load of 8 ohms?
If you mean as pairs, yes. put an 8 Ohm and a 16 Ohm speaker in parallel for each channel. The 16 Ohm speakers will take 1/3 the power and the 8 Ohm speakers will take 2/3 the power. The resulting impedance will be 5.33 Ohms.
How do i Make a 8 ohm speaker 16 ohm?
You can't change the ohm load of a speaker. What you can do, is get a second 8 ohm speaker to run with that speakers in series and you will get a total ohm load of 16 ohms.To run them in series, simply wire the positive terminal of one speaker to the negative of the other speaker. One speaker will have an open positive terminal which you wire to the positive terminal on the amp, and same goes for the negative on the other speaker (to the amp's negative terminal of course).
Can you wire 2 16 ohm speakers to 16 ohms?
No. Two 16 ohm speakers connected together are either 32 ohms, if wired in series, or 8 ohms, if wired in parallel. You can, however, connect four 16 ohm speakers in series-parallel to get 16 ohms, with four times the power handling capacity of just one.
Is it ok to hook a 16 ohm Speaker up to a 8 ohm amp?
A1: The output impedance of a power amplifier is always less than 0.1 ohms. There are no 8 ohm amplifiers on the market! A2: I actually just bought a new car radio/CD player that specifically shows 4 ohm speakers on the sticker. It is designed to work optimally with 4 ohm speakers. If you use 8 ohm instead, it will work, but you will not get the full power output that is specified. The amp can only kick out so much voltage and so much amperage - if it is designed for 4 ohm speakers, and 200 watts (stereo, so 100 watts per speaker), it can supply 20 volts (P = V^2 / R). If you used 8 ohm speakers to this amplifier, each speaker would only get 50 watts powered at full output voltage. Alternatively, if it is designed for 8 ohm speakers and 100 watts per speaker, it can provide 40 volts. If you used 4 ohm speakers instead, each speaker could be given 200 watts at 40 volts, resulting in severe overheating and damage to the amplifier. This applies to your case as well: it is OK to hook up higher impedance speakers to a lower impedance amplifier, but you will get less power delivered. If you do the opposite (lower impedance speakers to higher impedance amplifier), keep the volume low or you could burn out the amp.
If you have a 100 watt amp can you just have two 50 watt speakers instead of a 100 watt speaker?
Maybe.The real question comes down to the resistance of the output on the amp vs. the resistance of the speakers. You'll have to do a little math and understand the difference between series and parallel wiring. Throw back to high school physics.When you're wiring something in series the resistances are added. So, if you have two 8 ohm speakers the total resistance is 16 ohms. If the output resistance on the amp is 16 ohms, you're in good shape, but don't crank it or it definitely will blow.When you wire a parallel circuit you use the formula 1/RT=(1/R1)+(1/R2). Again, if both speakers are 8 ohms then it's 1/RT=(1/8)+(1/8). With a little math you get 4 ohms. This is WAAAAAAAY different from 16 ohms. Turn that 16 ohm amp on now and those speakers will turn into a fun light show, but they'll be toasted. Throw some butter on it and you've got breakfast.
What ohm load will 4 12 in dual 2 ohm play at?
There are a lot of possibilities here, especially since your question is worded exactly right.I'm taking it you have 4 12" speakers, each of which have Dual Voice Coils (2 Ohms each). You want to wire them together and see what ohm load you have.Ok, there's multiple ways to wire this up. Series, Parallel, and Series/Parallel combo.Wiring these speakers in series can give you either a 4 ohm load, or a 16 ohm load. 4 ohms if each speaker by itself (having DVC) is wired in parallel and 16 ohms if each speaker by itself is wired in series.Wiring these speakers in parallel can give you either a .25 ohm load, or a 1 ohm load. Again .25 ohms if each speaker by itself (having DVC) is wired in parallel and 1 ohms if each speaker by itself is wired in series.Wiring these in a series/parallel configuration can give you tons of different wiring options and ohm loads. In your case .75, 1, 3.2, 4 ohm loads.So your best option would to be wire your speakers up in series, with each speaker wired in parallel to itself. This way you'll get a 4 ohm load, if done properly. Make sure your amp can run a 4 ohm load too.
