Want this question answered?
The intermediate frequency (IF) amplifier lies between the mixer and the demodulator. The mixer shifts the input radio frequency (RF) signal into the range of the IF amplifier. The IF amplifer is a band pass amplifier, so only RF signals that are the IF frequency distance away from the local oscillator in the mixer can pass through to the demodulator. This process is called the superhetrodyne process.
I suspect you mean an "Intermediate Frequency transformer", or IF transformer. Superheterodyne (Or superhet) receivers convert the frequency of an incoming signal to a special frequency called the "Intermediate Frequency" or "IF". Most of the amplification takes place in the IF Amplifier which usually has several stages. Each of these stages is coupled to the next stage by a tuned transformer called an IF transformer. For AM receivers, the Intermediate frequency is usually 455 KHz, and for FM receivers it is usually 10.7 MHz. These transformers are usually about 20 turns of Litz wire on a plastic former with a dust-iron adjustable core. It sits in a little metal shield can.
No effect on frequency but increases it's amplitude.
all reactive elements in the amplifier, including stray capacitances and inductances.
75khz
radio frequency amplifier intermediate frequency( If strip) in a superheterodyne radio mixer /demodulator Audio amplifier
The intermediate frequency (IF) amplifier lies between the mixer and the demodulator. The mixer shifts the input radio frequency (RF) signal into the range of the IF amplifier. The IF amplifer is a band pass amplifier, so only RF signals that are the IF frequency distance away from the local oscillator in the mixer can pass through to the demodulator. This process is called the superhetrodyne process.
Is this sentence supposed to be question? Any superheterodyne receiver will have an IF amplifier. It doesn't matter whether TV or radio.
I've seen 455kHz, 10.7MHz and 70MHz intermediate frequencies. There is, however, no law that dictates the IF you run...some very sensitive receivers even use multiple IF stages.
High frequency amplifier is a device which is tuned by high frequency. Tuned means the overlapping of generated frequency with that amplifier.
Selective amplifier is an RF amplifier which selects particular frequency and amplifier so it can operate at fixed frequency.
In communications and electronic engineering, an intermediate frequency (IF) is a frequency to which a carrier frequency is shifted as an intermediate step in transmission or reception. [1] The intermediate frequency is created by mixing the carrier signal with a local oscillator signal in a process calledheterodyning, resulting in a signal at the difference or beat frequency. Intermediate frequencies are used in superheterodyne radio receivers, in which an incoming signal is shifted to an IF for amplification before final detection is done. The intermediate frequency stays the same for all signals, for example 455 kHz in an AM broadcast receiver.Conversion to an intermediate frequency is useful for several reasons. When several stages of filters are used, they can all be set to a fixed frequency, which makes them easier to build and to tune. Lower frequency transistors generally have higher gains so fewer stages are required. It's easier to make sharply selective filters at lower fixed frequencies.
The intermediate frequency in the superheterodyne receiver is chosen as the desired compromise between sensitivity and selectivity. 455kHz is used in AM broadcast applications, while 10.7mHz is used for FM. The IF stage is tuned for a steep skirt passband at that frequency, allowing only the desired heterodyned (shifted) input signal to make it through to the demodulator.
A; An amplifier will have no effect on the input frequency however its output may not follow the input frequency at the hi end due to the amplifier limitations
what is the reasion of using intermediate frequency in television system
I suspect you mean an "Intermediate Frequency transformer", or IF transformer. Superheterodyne (Or superhet) receivers convert the frequency of an incoming signal to a special frequency called the "Intermediate Frequency" or "IF". Most of the amplification takes place in the IF Amplifier which usually has several stages. Each of these stages is coupled to the next stage by a tuned transformer called an IF transformer. For AM receivers, the Intermediate frequency is usually 455 KHz, and for FM receivers it is usually 10.7 MHz. These transformers are usually about 20 turns of Litz wire on a plastic former with a dust-iron adjustable core. It sits in a little metal shield can.
frequency response curve helps us to find the bandwidth of particular amplifier circuit. Bandwidth is the range of frequency at which the amplifier works better....