0
In a woman's sense what is a coil and how do they insert it and take it out?
Wiki User
∙ 15y ago
A "coil" is one variety of Intra-Uterine Device" or IUD, which is a birth-control device implanted into the uterus. It prevents an embryo from implanting itself in the uterus.
It is inserted through a tiny tube through the vagina and cervix, where it expands.
There are two removal cords which remain in the vagina, where they are generally unnoticeable.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you change ignition coil on suzuki Verona?
Take off the plastic engine cover , take out the bolt that hold the coil , take out the coil.
How do you take off the emissions coil on a 1994 geo prizm?
how to take off an emissions coil on a 1994 geo prizm
How do you replace a 1970 Chevy ignition coil?
take the wires off the + and - side of the coil, pull the coil wire out of the coil, unbolt the coil from the manifold, to install just reverse directions.
How do you test a 91 Chevy beretta dis coil?
Take off the modual and coil pack take it to autozone they will test it free.
What is meant by a primary coil and a secondary coil?
In a transformer, the primary coil is the coil that has voltage applied to it. The secondary coil is the coil that we take voltage from. Transformers are used to step up voltage, step down voltage, or simply to isolate circuits.
How do you front freak?
Well, it's simple, really. You just insert, take out, insert, take out, until one or the other has an orgasmic perfection.
How do you replace a coil pack on a 2000 Chevy Malibu?
disconnect wires and label them,each coil has its own screws holding it to plate,take out scews,pull coil straight up do not bend the coil tangs at mounting of coil. Do this for each coil! HOPE THIS HELPS!
If the AC has an outside line that is freezing then how do you check to see if the coil needs to be cleaned and is the coil inside?
The coil is inside. Check to see if the filter is dirty as well. To clean the coil you must remove the front panel to the evap coil. If you have a flat coil you must slide the coil out to clean it. If you have an A coil, take off the plate on the front of the coil and you should be able to visually inspect the coil. It is important that you do not mash the dirt into the coil fins.
How do you change coil spring on clio?
Take it to a garage
What are the different ways to induce current in a coil?
Different ways to induce current in a coil are as given below:(1) If a magnetic field is changed round a coil then an induced current is set up in the coil. It can be done by taking a bar magnet and bringing it closer to the coil or taking it away from the coil.(2) If a coil is moved in a magnetic field, then again an induced current is set up in the coil.(3) If a coil is rotated in a uniform magnetic field, it may also cause an induced current in the coil.(4) If we take two coils and insert them over a non conducting cylindrical roll then on changing current flowing in one coil, an induced current is obtained in the other coil.CommentYou don't induce a 'current' into a coil; you induce a voltage. If that coil is open circuited, then no current will flow. If, on the other hand, the coil is connected to a load, or its opposite ends short-circuited, then the induced voltage will cause a current to flow. Remember, current will only flow if there is a load, or short circuit, and the value of the current will depend upon the value of the induced voltage and the resistance of the load or short circuit.
When making a secondary coil for a Tesla coil is it ok to take two long copper wires and solder them together then coil it?
In the related links box below, I posted Building A 250,000 Volt Tesla Coil.
How do you replace ignition coil on 1984 Chevrolet celebrity?
If your car has the V6 engine the ignition coil is mounted to the intake manifold next to the distributor. First unplug the wires from the coil. Take note of which way they come out so you can put them back. Then take out the bolts that hold the coil in place on the intake manifold. The factory original coil is riveted to the mounting bracket, new coils come without the mounting bracket. You will need to take the rivets out to remove the old coil from the bracket. The new coil come with screws to mount the coil to the bracket Once the coil is mounted to the bracket then put the bracket back on the intake manifold. Plug the wires back in, that should do it.
