0
Input! x
Wiki User
∙ 13y ago
Anonymous
Anonymous
A chip and pin is an input device x
Add your answer:
Earn +20 pts
I've found a pin and I'm not sure it's a navy pin from ww 2 or the boyscoutsWhat is the eagle cross pin?
Would have to be more specific but sounds like a pin from the WW1/WW2 era
What does the 11th Armored Division pin symbolize?
If this is the pin then here is an explanation. 241st Field Artillery Regiment DI
Post command do you wear the command at sea pin if you have two warfare devices?
I would think so. I've met a former CO who wore his dolphins, boomer pin, and command at sea pin at the same time.
What is your pin for Memphis public library?
your pin is the last four digits of your library number on your card. THIS IS ONLY FOR MEMPHIS PUBLIC LIBRARY
How do I find out what my Olympic pin set is worth?
how much is my limited edition collectors pin #2-1982/198 complete set worth
What is the input of an Chip and pin payment device?
There both
Explain the pin dia gram of IC 7812 belonging to category of logic gates?
The 7812 is not a logic gate. It is a three terminal voltage regulator with an output of +12V.Looking at the pins of the TO-220 device, with the flat side down, the left pin and the case is common, the center pin is input,and the right pin is output. For the smaller TO-92 78L12 device, the left pin is output, the center pin is common, and the right pin is input
Is adc present on chip in 8051 or not?
There is no formal adc input on the 8051. However, the CMOS version of the chip can use a technique involving a resistor, diode, and capacitor, along with a bidirectional pin (or one output pin and one input pin) to implement a "quick and dirty" adc function. You discharge the capacitor and then let it charge to the voltage of the input. You measure the time it takes to see the input pin change, and you calculate the input voltage.
How IC 7402 can be connected to use NOR gate?
IC 7402 is different from the other type of IC like 7404,7408,7432 and 7400 when it is connected to have an output desired... if you noticed all i mentioned ic is connected from left to the right. input pin 1 and 2, output pin 3 input pin 4 and 5, output pin 6 input pin 13 and 12, output pin 11 input pin 10 and 9, output pin 8 while in nor gate, to have the desired output it must be connected from right to left... input pin 2 and 3, output pin 1 input pin 5 and 6, output pin 4 input pin 8 and 9, output pin 10 input pin 11 and 12, output pin 13
What is the pin diagram of Integrated Chip L293D?
L293D is having 20 pin IC and also 16 pin IC. description of 20 pin is: 1-enable 1 2- input 1 3- output 1 4,5,6,7,14,15,16,17- ground 8- output 2 9- input 2 10,20-vs 11-enable 2 12- input 3 13-output 3 18-output 4 19-input 4 description for 18 pin: 1-enable 1 2- input 1 3- output 1 4,5,12,13- ground 6-output 2 7- input 2 8,18-vs 9-enable 2 10-input 3 11-output 3 14-output 4 15-input 4
What data is output in a monitor in a supermarket?
Barcode Scanner. Touch Screen. Chip and Pin Device. Magnetic Strip Reader. Keypad. Keyboard.
What are disadvantages of a chip and pin device?
Security
What is 3 rd pin of op amp?
I should expect a real-world op-amp to have 5connections:-- the inverting signal input-- the non-inverting signal input-- the signal output-- the power supply input-- the ground connection.
What is the Use of 7408 IC?
a 7408 ic chip is a quadruple, 2 input AND Gate chip. These chips have 14 pins. Pin 7 is gnd and pin 14 is vcc. In principle, an AND Gate is just that. A gate that is Active high. To get an active high output, you must have both inputs active high. 5 volts on each input will give you a 5 volt output. These IC chip use TTL (transistor-transistor logic). They are obsolete and are no longer used in todays electrical circuits. Most electronic systems use a large CPLD, Complex Programmable Logic Device, that can be used to implement digital logic designs that contain 20,000 or fewer gates. Texas Instruments poineered the TTL 7408 IC chip. CPLD boards are commonly made by a company named Altera
What is the maximum number of inputs you could have on say an OR gate If it were a 16 pin chip could you have 14 pin inputs one Vcc and on GND?
You need an output pin as well, so in the example of the 16 pin chip, you could have 13 inputs.
Why first pin of ic 7806 is used as input?
Because that is the way the chip was designed. No special reason.
What is the use of offset null pin in integrated circuits?
Pin used to eliminate the effect of internal component voltage on the output of the device.
