0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Why diode don't allow the current coming in opposite direction?
Diode is known as a rectifier because it only allows the current to flow in one direction. Diode is only effective when the input is AC.
What is the effect of diode voltage drop as the output voltage?
The effect of diode voltage drop as the output voltage is that the input voltage will not be totally transferred to the output because power loss in the diode . The output voltage will then be given by: vout=(vin)-(the diode voltage drop).
What is the output of a diode can be?
A diode itself has no input or output.The circuit containing the diode usually has an input and an output, maybe even more than one of each. The output of this circuit will depend on far more than the diode as well as depending on the type of diode used.Theoretically: if a diode is connected across the secondary output of a stimulated transformer, you would read a half wave at the frequency of the source across diode.Such a circuit would cause any real diode to explode due to lack of any current limiting and the resulting high power dissipation in the diode.Hence "Theoretical". That's kind of what "Theoretical" means.
Can an OR gate have one input?
Technically, an OR gate could function with only one input, in which case it would perform the same as if it was not present; when its only input goes high, it would go high, and when the input goes low, it would go low. As a practical matter, the only useful purpose of a single input OR gate would be to have it act as a simple diode, which would be more efficient to simply have a diode in its place.
What is formula for zener diode comparator?
A: There is no formula it is a comparison of the zener diode voltage to the other input when one exceed the other the comparator will change state on the output and decreasing will return to the previous state
How does the cut in voltage effects the output of a diode clipper?
For answering this question we have to consider the constant voltage drop model of the diode which says that if voltage across diode is less then its cut in voltage than assume diode to be open circuit and if it is greater then assume diode to be short circuit.Till the input voltage is less than the cut in voltage, diode is open circuit(thus no current through the circuit). Thus entire input voltage appears across the diode as output.When input voltage is greater than or equal to cut in voltage, then short circuit the diode. Thus, there will be no voltage drop across the diode as output.Thus cut in voltage decides when to consider the diode open circuit and when short circuit. It decides when the diode will have output when it will not.
Is washing machine is an input out put device?
The input process of a washing machine are dirty clothes, detergent, and water are put into the washing machine. The washer washes the clothes and the output process is clean clothes.
What is envelope detection?
When an AM signal is received, the receiver must perform a converse process to get the original signal ( Information Signal ) back . This process is known as detection or demodulation, the simplest process which is used widely in AM radios is the Envelop Detector . Envelop Detector is an electronic circuit which is used to recover ( Demodulate ) the original signal in AM systems, its constructed from just one diode, one capacitor and one resistor . This is essentially just a halfwave rectifier which charges a capacitor to a voltage = the peak voltage of the AM signal . However .. the output of the detector follows the envelop of the modulated signal. On the positive cycles of the input signal, the diode conducts and the capacitor charges up to the peak voltage of the input signal. As the input falls below this peak value, the diode is cut off, because the capacitor voltage is greater than the input signal voltage, thus causing the diode to open. The capacitor now discharges through the resistor at slow rate . The discharge process continues until the nest positive half-cycle. When the input signal becomes greater than the output across the capacitor, the diode conducts again and the process is repeated .
What is the input process and output in service industry?
Input : What is put into the industry. Process : What is done to the inputs to acheive the finished product. Output : What you have made/produced. Example of an Argricultral Industry: Cow (Input) Milking (Process) Milk (Output) Hope this helps you!! :D
A silicon avalanche photo diode is fabricated by what process?
A silicon avalanche photo diode is fabricated by the process called impact ionization.
Disadvantage of using diode as shunt element in clipper circuit?
In shunt clippers, when the diode is in off condition, transmission of input signal must take place to output. But in the case of high frequency input signals, diode capacitance affects the operation of circuit adversely and the signal gets attenuated (which means that, it passes through diode capacitance to ground).
Why diode don't allow the current coming in opposite direction?
Diode is known as a rectifier because it only allows the current to flow in one direction. Diode is only effective when the input is AC.
Why diode logic gate is not suitable for cascading operation?
the pullup or pull down resistance in the diode logic gate makes it a high output resistance device.If u try to drive another diode logic gate with it the output voltage of the first gate will be affected by the resistance in the second gate.A diode logic gate should always drive a high input resistance input.
What is the result or product of a process called?
output the result
Is a gamepad an input output storage or a process device?
A gamepad is an input device. Information is sent from the game pad and put into the computer, which will process it. An output device would be something like a printer or monitor.
What is the effect of diode voltage drop as the output voltage?
The effect of diode voltage drop as the output voltage is that the input voltage will not be totally transferred to the output because power loss in the diode . The output voltage will then be given by: vout=(vin)-(the diode voltage drop).
Why is input resistance low and output resistance high in transistor?
The input resistance of a trasister is jst like pn junction of a diode which has a breakdown voltage of .7v for silicon and the output resistance is like a reverse bias of a diode and hence the resistance is high
