Yes you just have to "steal" power from the switch. Do this by running a pigtail wire from the hot of the switch to the hot wire of the plug. Make sure you do this before the switch or you will end up with your outlet being switched as well.
Some rooms have an outlet controlled by a light switch at the door. This is normally in bedrooms. It is possible that the switch is wired to only one of two outlets in a duplex outlet since it is easy to configure a duplex outlet to separate the bottom and top outlets.
The first is taking power to a garden shed or other outbuilding, and the second is installing an outdoor socket outlet for your garden power tools.
Bring power into the switch box with a 12/2 or 14/2 wire and send power from there to the wall outlet with another 12/2 or 14/2 wire depending on the circuit. 12/2 for 20 amp and 14/2 for 15 amp circuit. You will now have 2 sets of wires in the switch box. Connect all the whites together under a wire nut and push them back into the box. Connect all the ground wires together and attach them to the green ground screw on the switch. Connect the black wire from the power source to one of the screws on the switch, does not matter which one. Then connect the black wire going to the outlet to the other screw on the switch. Put the switch back in the box and install the cover. At the wall outlet connect the ground to green ground screw, white wire to silver screw, and black wire to gold screw on one of the outlets. Run 3jumper wires from all three of those screws to the other outlet in the box. Ground to ground, black to gold, and white to silver screws. Put it in the box and install the cover.How_do_you_wire_a_outlet_to_work_from_a_light_switch
You will need a receptacle that you can wire each outlet separately (not jumpered). You would then wire the switch in series on the line conductor with the outlet you want switchable. Wire the other outlet directly to the power source. You can jumper the neutral from one outlet to the other.
There are several possible causes for an electric outlet not working:The outlet has gone bad such as internal contacts corroded or bent so they don't make a connection.The wire on the outlet is not connect or loose, not connected properlyThere is a break in the wire somewhereNo power going to the outlet from the source, which could also be caused by a bad fuse
You need to run a wire from the existing power source to switch to switch to switch to outlet.
drill hole in dashboard, install outlet in hole, and run two wires to the battery
Some rooms have an outlet controlled by a light switch at the door. This is normally in bedrooms. It is possible that the switch is wired to only one of two outlets in a duplex outlet since it is easy to configure a duplex outlet to separate the bottom and top outlets.
Change the wall outlets
Connect the incoming power to the line side of the GFCi outlet. Now run another wire connected to the line side of the GFCI outlet from the GFCI outlet to the switches. Power one of the switches and use that switch to turn on the 2 lights. Run power from that switch to another switch and use that switch to send power to the fan. Mount both switches in a double pole switch box. If the light above the sink has an outlet on it then you will have to connect power going to that light on the load side of the GFCI outlet. If not then just connect it to the line side.
You turn on power to the accesories, ie radio, power outlet, etc.
If you are referring to a switched UK-style socket outlet fitted with a led, or a wall switch fitted with a led, then the led merely indicates that the socket outlet switch or wall switch is in the 'on' position.
Yes
The first is taking power to a garden shed or other outbuilding, and the second is installing an outdoor socket outlet for your garden power tools.
Uh, because you left the switch on for what you had plugged in to the outlet.
The steps to switch on a computer begin with making sure that the computer and its peripherals are plugged into an electrical outlet. Turn the power switch on the electrical outlet and press the power button on the computer tower. Turn on the computer monitor and wait for the computer system to start up.
Just put a switch in the power wire going to the coil.