0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the output voltage of digital receivers?
The output voltage of a digital receiver will vary depending on the design and manufacture of the particular receiver, and the output system used. It is normally quite low, typically between 1 and 5 volts, ranging up to 12 for some SCART connections.
Why same junction box is not used for digital and analog signals?
Signal crosstalk. Most specifically is high speed digital switching noise being picked up by analog circuits and upsetting their operation.
Important factors that can be used to comparing the various digital-to digital encoding schemes?
A lack of high-frequency components means that less bandwidth is required for transmission. In addition, lack of a direct-current (dc) component means that ac coupling via transformer is possible. The magnitude of the effects of signal distortion and interference depend on the spectral properties of the transmitted signal. Clocking: Encoding can be used to synchronize the transmitter and receiver. Error detection: It is useful to have some error detection capability built into the physical signaling encoding scheme. Signal interference and noise immunity: Certain codes exhibit superior performance in the presence of noise. Cost and complexity: The higher the signaling rate to achieve a given data rate, the greater the cost. Some codes require a signaling rate that is in fact greater than the actual data rate
What are the differences between analog and digital filters?
The ANALOG FILTER used in analog circuits.The DIGITAL FILTER USED IN DIGITAL circuits.
Is AGC are used in oscillator or in receiver?
Yes, It is.
What is a optical audio cable used for?
An optical audio cable is used to transmit digital audio (AC-3) signal from the source to the receiver, such as from a DVD player to a digital audio amplifier/receiver. You can transmit 5.1 dolby digital or DTS surround sound with an optical audio cable, same as digital coaxial audio cable.
Why is Avalanche photo diode used when compared to PIN diode?
The output current of a PIN diode is proportional to the light incident . Whereas in APD due to internal multiplication (Avalanche multiplication) of primary photocurrent, higher gains are possible. A small signal current output from the pin diode are to be amplified before applying to next associated receiver circuit. This includes thermal noise in the main signal, giving lower, receiver sensitivity. In case of APD, photocurrent is multiplied before encountering the thermal noise amplifier, giving increased receiver sensitivity.
What is a sensar?
A Sensar is a type of digital ready TV antenna from Winegard. The two versions of the Sensar antenna of an amplified and an unamplified version. They can be used for homes.
What is an ATSC tuner used for?
ATSC stands for Advanced Television System Committee. It allows for the reception of digital television in digital televisions. It is also called an ATSC receiver.
Why you need modems on digital circuits?
In digital circuits modem is used to multiplex and demultiplex the digital data.multiplexing means the digital signals amplitude or frequency or phase is varied with a carrier signal.at the receiver end the carrier signal is separated out and original digital signal is received
What type of noise occurs when you do not understand the speakers words or gestures?
Semantic Semantic noise, the third type of noise, occurs when the receiver of a message doesn't understand a word or gesture used by the sender or has a different meaning for the word or gesture.
What is the output voltage of digital receivers?
The output voltage of a digital receiver will vary depending on the design and manufacture of the particular receiver, and the output system used. It is normally quite low, typically between 1 and 5 volts, ranging up to 12 for some SCART connections.
What people meant by Master Pin code or Key when they talk about a Digital Satellite Receiver Why and how the key of a specific digital satellite receiver is used?
Yet another sat receiver hacking question?Do your research on the 'net. It's all there, but you need to actually take the time to read what people are writing, rather than ask questions. This isn't the forum for finding information about illegal activities such as satellite receiver hacking.
What are digital hearing aids used for?
Digital hearing aids are used for individuals that are hard of hearing and this new technology is perfect by amplifying sound using noise reduction. It sorts and processes sounds from the environment to your ear.
What are the advantages and disadvantages of instrumentation amplifier?
Advantages:Even a small value of input voltage can be amplified using instrumentation amplifier.Disadvantages:For transmission purpose for long range, noise also gets superimposed along the original wave. Therefore specific cables are used to reduce noise.
Motorola digital cable box?
A Motorola digital cable box is used to changed an analog television to digital viewing. The cable box needs to be connected to a receiver such as a roof antenna and then to the television. The television then has to scan the box to locate signals that it can receive.
What is meant by Bit energy to Noise ratio?
Bit Energy-to-Noise Density (Eb/N0) is the ratio of bit energy to noise density. This value is used to specify the lower limit of operation in most digital communications systems and is also used to measure radio channel performance.
