0
Is there any disadvantage of selecting over rated circuit breaker?
Wiki User
∙ 13y ago
If i understand you correctly, yes there certainly can be. If you replace, say a 10 amp breaker with a 20 amp. you are losing the safety factor - the whole purpose of the breaker to begin with. Always replace a breaker with the exact same amperage rating!
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Is the main circuit breaker is a sum of the sub circuit breaker?
Typically yes because that is what makes sense. However, the subpanel could have the same size breaker as long as the panel were rated for that amperage and the wire sizes were appropriate.
What is a difference between 10KA and 22KA circuit breakers?
The previous answer is incorrect, and I would advise that user to not give out information if they are going to give completely misguided information. The interrupting rating of a breaker is the maximum current that the breaker is designed to handle, at the breaker's rated voltage, before damage will occur to the breaker. A breaker will trip at FAR LESS than the interrupting rating, but it is extremely dangerous to expose the breaker to any situation where it will have more than the rated interruption current. the breaker is designed for. The reason some breakers are rated at 22kA instead of 10kA is because they typically have far larger conductors hooked up to them, so with the lowered impedance on the circuit there is more of a chance for the breaker to experience a higher fault current at the breaker. So electricians install 22kA breakers to handle the higher "available fault current."
Can 11kv breaker be installed on 6.6kv line?
Yes. But,circuit breaker are usually rated in terms of current they can interrupt,not the voltage.
What is the difference between rated short circuit duration 3 seconds and 1 second circuit breaker?
The energy dissipated.
Why not to overload a socket?
Yes! A socket is a part of a circuit. Usually there are a number of sockets and lights associated with a specific circuit. The wiring of the circuit and the circuit breaker are limited to a specific amperage. If you exceed the amperage, you can blow the breaker. If the wire is rated for 15 amps and the circuit breaker is rated for 20 amps, the wires can overheat and cause fires.
How do you calculate rated kva of a circuit breaker?
You don't calculate the rated kV.A of a circuit breaker; it's determined by the manufacturer. It's important that a circuit breaker's rated kV.A exceeds the fault level kV.A at the point where the circuit breaker is located, otherwise it may fail to interrupt a fault current and, possibly, self destruct.
Is the main circuit breaker is a sum of the sub circuit breaker?
Typically yes because that is what makes sense. However, the subpanel could have the same size breaker as long as the panel were rated for that amperage and the wire sizes were appropriate.
What circuit breaker to install for 10 amp 250 volt circuit?
You need a breaker rated for 10 amps and 250 volts. The breaker must also fit properly in your panel.
What size circuit breaker is needed for a 300 watt bulb?
A 15 amp circuit breaker will handle this situation very well. The smallest home breaker is rated at 15 amp.
What is making capacity of a circuit breaker?
Hard to define... A four year old child has the strength to physically "make" a typical household circuit breaker, while a teen would be able to "make" a typical industrial circuit breaker. (The latter breaker being physically much larger than the former.) Circuit breakers have their "breaking capacity" rated in AMPS. A typical household breaker is rated at 20, 30 or 50 Amps. Industrial breakers might be rated at 500 amps or a thousand or even more. Hope this helps but if it didn't answer your question, please rephrase it and ask again.
How are Branch circuit protected?
Branch circuits are protected by the circuit breaker found in the electrical panel. Each circuit should have its one breaker. The breaker should be rated to protect the insulation of the wire, so you can determine the breaker size based on the circuit conductor size Example #14-2 should be protected by a 15 amp breaker
What is exactly answer of circuit breaker?
A circuit breaker is an overcurrent protection device. As well as being able to open and close a circuit supplying its rated load, a circuit breaker must also be capable of interrupting and closing onto an overcurrent, including a short-circuit fault, without damaging itself.
What is a difference between 10KA and 22KA circuit breakers?
The previous answer is incorrect, and I would advise that user to not give out information if they are going to give completely misguided information. The interrupting rating of a breaker is the maximum current that the breaker is designed to handle, at the breaker's rated voltage, before damage will occur to the breaker. A breaker will trip at FAR LESS than the interrupting rating, but it is extremely dangerous to expose the breaker to any situation where it will have more than the rated interruption current. the breaker is designed for. The reason some breakers are rated at 22kA instead of 10kA is because they typically have far larger conductors hooked up to them, so with the lowered impedance on the circuit there is more of a chance for the breaker to experience a higher fault current at the breaker. So electricians install 22kA breakers to handle the higher "available fault current."
Can 11kv breaker be installed on 6.6kv line?
Yes. But,circuit breaker are usually rated in terms of current they can interrupt,not the voltage.
What causes circuit breaker to trip even when it's properly rated?
A circuit breaker is dual function. The only time it will trip is if it senses a fault current that is rated higher than the breaker rating (short circuit). The other trip condition is if the circuit is overloaded and is drawing a current higher than the breaker rating. On breakers that protect motor feeders the breaker has to be rated 250% higher than the motors full load amperage. If the breaker has lots of use and is used for a switch being manually turned off and on will weaken the trip value of the breaker. If you have access to, or know an electrician, a clamp on amp meter on the conductor that the breaker feeds will tell you what is happening. Clamp the line and turn on the load to see exactly what the current is. If, like you say, the breaker is properly rated and the current is within the breaker limits then change out the breaker for a new one.
What is the difference between rated short circuit duration 3 seconds and 1 second circuit breaker?
The energy dissipated.
A small appliance circuit will be protected by a circuit breaker rated at?
Yes, it will be protected by a circuit breaker or fuse. The normal rating of the circuit breaker or fuse is 25% more than the maximum current expected, or the maximum current allowed for the cable size, whichever is lower.
