VW Vanagon
Ford Crown Victoria
DIY Projects

Is there any easy way to change the side-marker bulbs in an 2002 ford crown vic?

373839

Top Answer
User Avatar
Wiki User
2011-09-13 05:59:14
2011-09-13 05:59:14

IT not to hard to change .take the Phillips screw out on the side of the marker lamp then open the hood and open the plastic black door behind headlamp. you will need a 11 millermeter wrench or socket .take the bolt off the back of the marker lite and it will come right out.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

If you can't access the bulbs take the light assy off and turn the bulbs counterclockwise to remove them

User Avatar

how to change headlight on a vw polo 02

User Avatar

http://wiki.answers.com/Q/How_do_you_change_the_fog_lamp_bulbs_on_2002_Chevy_Impala

User Avatar

Have to remove the oil pan to get to the pump.

User Avatar

Bad Lamp on that side. Change all bulbs.

User Avatar

Go to AutoZone, when you purchase the bulbs, they'll install for free

User Avatar

According to the 2002 Ford Crown Victoria Owner Guide : With engine oil filter change : ( 5 quarts / 4.7 liters of engine oil )

User Avatar

how do I replace interior light bulbs in 2002 chevy impala. I removed the cover, but the bulb is cramped in and I can't pull it out.

User Avatar

Remove the headlight assembly to gain access to the bulbs.

User Avatar

Low beams - 9006 bulbs or HB4 bulbs High beams - 9005 bulbs or HB3 bulbs

User Avatar

The 2002 Chevy Avalanche does not have user replaceable radio bulbs. The radio needs to be dismantled by a qualified technician to replace the bulbs.

User Avatar

See Tail/Stop/Turn Signal and Sidemarker Lamps on page 6-38 of your "Owner's Manual", under Section 6: Service and Appearance Care - Bulb replacement...

User Avatar

Remove the headlight assemblies and you will have access to the signal bulbs. See sources and related links below for bulb information.

User Avatar

where is the DPFE sensor located on a 2002 ford crown victoria?

User Avatar

On my 2002 Bravada open hood and there are 2 clips that have to be lifted and entire headlight assembly pulls out allowing acces to bulbs-perhaps the same with yours

User Avatar

The brake light bulbs ar removed from the rear of the light assy . Take it off of the body.

User Avatar

5 quarts WITH ENGINE OIL FILTER CHANGE , according to the owners manual

User Avatar

Unless you are an electronics wiz you change the entire light. If you are an electronics wiz you can get your local electronics supplier to match up the led bulbs with a sample.

User Avatar

There are no wires to change - coil over plug. To change the plugs unscrew the old ones. put the new ones in their place. Torque to spec.

User Avatar

According to the 2002 Ford Crown Victoria Owner Guide : ( " regular " unleaded gasoline , 87 octane )

User Avatar

What size bulbs in vanity mirror on a 1999 ford explorer?

User Avatar

a 2002 p71 crown Victoria has about 235 to 240 hp that mean the car will get up 0-60 in 7 secends

User Avatar

Remove the 3 nuts from behind the housing in the trunk. Gently pull housing from car.

User Avatar

2002 ford crown Victoria how to repair crank sensor?


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.