Want this question answered?
In all branches of a parallel circuit, it is voltage that is the same. Across each parallel branch of a circuit, we'll measure the same voltage. Probably the best example of equal voltages appearing across all branches of a parallel circuit is a household electrical distribution curcuit. The voltage at any outlet where you'd care to plug in an appliance or device will be the same. A fan plugged into an outlet in a bedroom will "feel" the same voltage as it would if it were in the living room and plugged into an outlet there.One other way to look at things like this is that each branch of the parallel circuit is connected across the voltage source. Each branch could be looked at as an "independent" circuit, and any given branch doesn't care what is happening in any other branch. Does turning that fan we mentioned on and off, or even unplugging it from the outlet affect the operation of, say, the refrigerator? No, it does not. Any device plugged into an outlet is connected "directly" to the source of voltage. And each parallel branch of the circuit will operate independently of any other branch. We know that the voltage in (or across) any branch of a parallel circuit is the same as the voltage across any other branch.
Measure the voltage appearing across each resistor. If they are identical, and equal to the supply voltage, then the resistors are in parallel.
The voltage drop in any branch (closed loop) of a series parallel circuit is equal to the APPLIED VOLTAGE(NOVANET) Without looking in my codebook, I believe it is 2% on a branch circuit.
The voltage would 9V minus any drop in the battery.
all the sockets are always connected in parallel,due to this the voltage across each soket is same. when any socket is open then there is no voltage loss..so the votage is same like line voltage.
The voltages appearing across each branch of a parallel circuit will be equal to the supply voltage.
In all branches of a parallel circuit, it is voltage that is the same. Across each parallel branch of a circuit, we'll measure the same voltage. Probably the best example of equal voltages appearing across all branches of a parallel circuit is a household electrical distribution curcuit. The voltage at any outlet where you'd care to plug in an appliance or device will be the same. A fan plugged into an outlet in a bedroom will "feel" the same voltage as it would if it were in the living room and plugged into an outlet there.One other way to look at things like this is that each branch of the parallel circuit is connected across the voltage source. Each branch could be looked at as an "independent" circuit, and any given branch doesn't care what is happening in any other branch. Does turning that fan we mentioned on and off, or even unplugging it from the outlet affect the operation of, say, the refrigerator? No, it does not. Any device plugged into an outlet is connected "directly" to the source of voltage. And each parallel branch of the circuit will operate independently of any other branch. We know that the voltage in (or across) any branch of a parallel circuit is the same as the voltage across any other branch.
Measure the voltage appearing across each resistor. If they are identical, and equal to the supply voltage, then the resistors are in parallel.
The batteries can be connected in parallel or in series. In parallel, good batteries of the same voltage will have a total voltage across them equal to the voltage across one of them. Those batteries in series will have a total voltage equal to the sum of the voltage of each of the batteries.
The voltage across a battery in a parallel circuit is equal to the voltage across each bulb because Kirchoff's Voltage Law (KVL) states that the signed sum of the voltages going around a series circuit adds up to zero. Each section of the parallel circuit, i.e. the battery and one bulb, constitutes a series circuit. By KVL, the voltage across the battery must be equal and opposite to the voltage across the bulb. Another way of thinking about this is to consider that the conductors joining the battery and bulbs effectively have zero ohms resistance. By Ohm's law, this means the voltage across the conductor is zero, which means the voltage across the bulb must be equal to the voltage across the battery and, of course, the same applies for all of the bulbs.
The current through each resistor is equal to the voltage across it divided by its resistance for series and parallel circuits.
The voltage drop in any branch (closed loop) of a series parallel circuit is equal to the APPLIED VOLTAGE(NOVANET) Without looking in my codebook, I believe it is 2% on a branch circuit.
Kirchoff's voltage law: In a series circuit, the signed sum of the voltage drops around the circuit add up to zero. Since a parallel circuit (just the two components of the parallel circuit) also represents a series circuit, this means that the voltage across two elements in parallel must be the same.Kirchoff's current law: The signed sum of the currents entering a node is zero. In a series circuit, this means that the current at every point in that circuit is equal. In a parallel circuit, the currents entering that portion of the circuit divide, but the sum of those divided currents is equal to the current supplying them.
In a series circuit the current flow in each element is equal but voltage across the each element is differ. In a parallel circuit the voltage across the each element is equal but current flow in each element is differ.
In a parallel circuit, all the branches are joined together at their start and again at their end by a conductor (usually wire).Now, the surface of a conductor (ideally) is an equipotential surface. That is, any point of its surface has the same electric potential.And since the voltage across each branch equals the difference in electric potentials between its start and its end, and these potentials are the same for every branch, it follows that the voltages across each branch must be equal to each other.
The voltage would 9V minus any drop in the battery.
all the sockets are always connected in parallel,due to this the voltage across each soket is same. when any socket is open then there is no voltage loss..so the votage is same like line voltage.