Ford Ranger
Ford Ranger XL
Ford Ranger XLT

Location of intake air temperature sensor on 1994 Ford Ranger with 2.3 Liter 4 cylinder engine?

123

Top Answer
User Avatar
Wiki User
Answered
2009-11-23 03:24:23
2009-11-23 03:24:23

motorcraft.com has a picture of the sensor and it is threaded , so it's threaded into

the upper intake manifold somewhere ( at least that partially answers your question )

001
๐Ÿ˜‚
0
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Related Questions


The tension pulley is centerline with the engine and at the very top of the belt routing.


where is the number 3 cylinder located on a 2.5 ford ranger engine


There are ( 4 engine cylinders ) in a Ford Ranger 2.3 litre four cylinder engine


The 4 cylinder engine is 2.3 liters ( 140 cubic inches ) in a 1994 Ford Ranger


No , the 2.3 liter 4 cylinder engine in a 1997 Ford Ranger is not an interference engine


The gauge sender is located on the back driverside top of the head.


There was a 2.9 L - V6 engine available in the Ford Ranger from 1986 to 1992


No , the 2.5 liter - 4 cylinder engine in a 1998 Ford Ranger IS NOT an interference engine


Firing order for 1996 Ranger 4-cylinder engine is 1-3-4-2.



The 2.3 liter DOHC , 4 cylinder engine in a 2006 Ford Ranger has a timing CHAIN


The labor time for a 2000 Ford Ranger with a 4 cylinder engine is 10 hours, or roughly $900. It could be more depending on the year of your vehicle and for the 6 cylinder engine.


On your Ford Ranger with the 2.3 or 2.5 liter four cylinder engine , with Fords twin plug ignition system : The compression plugs are on the DRIVERS side of the engine


If this is in a Ford Ranger : ( 1989 to 1997 is a 2.3 liter four cylinder engine ) ( 1998 to 2001 is a 2.5 liter four cylinder engine )


Yes , the 2.5 litre four cylinder engine in a 1999 Ford Ranger is a Single Over Head Cam engine


In a 2000 Ford Ranger : ( the 2.5 liter four cylinder engine , which was the only four cylinder engine offered from the factory for a 2000 Ford Ranger , not like the 2001 model when they started with the 2.3 liter DOHC later that model year )


( YES ) according to the Gates website ( they make timing belts etcetera ) the 2.3 liter four cylinder engine in a 1996 Ford Ranger ( is NOT an interference engine )


Yes , according to the Gates website ( they make timing belts etc. ) the 2.3 liter four cylinder engine in a 1996 Ford Ranger is NOT an interference engine


can you tell me the location of the coolant temperuture on a 1996 f150 4.9 six cylinder engine


A 2001 Ford F-150 could have a V6 or V8 engine A 2001 Ford Ranger XLT could have a 4 cylinder or the 3.0 or 4.0 liter V6 engine


Code P1299: Cylinder Head Over Temperature Protection Active Indicates an engine overheat condition was detected by the cylinder head temperature (CHT) sensor. An FMEM Strategy called Fail-safe Cooling was activated to cool the engine. Engine cooling system concerns Low engine coolant level Base engine concerns


Only if you have the 2.5 liter four cylinder engine in a 2001 Ford Ranger . ( that engine has a timing BELT )


On my 2000 International with a Detroit series 60 engine the water temperature sensor is on the back of the engine, passenger side in the cylinder head. Gears


The engine coolant reservoir has a thread on cap which is the "radiator " cap for the 4 cylinder engine


On a Ford Ranger ( V6 engine ) bank 1 is the passenger side of the engine ( where the # 1 engine cylinder is ) and bank 2 is the drivers side of the engine The engine cylinder locations are numbered ( on a V6 engine in a Ford Ranger ) firewall 3 - 6 2 - 5 1 - 4 front of vehicle



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.