0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you thread a Massey Ferguson model 12 square baler?
first your two roll in their compartment,run under the little plate before exiting and then going thru the two tension aid springs and then both thru the 1st porcelain,then divide for each porcelain on needle and go tie at base of needle and then engage manually for tiyng knot and then rotate whole system by hand by turning the flywheel.Gidday, I am self-taught on the 503, but after threading the needle, I pass the twine straight up through the gap in the knotting mechanism, against the thingy with the multiple serrated discs, then tie it back to the bale density adjuster at the back. After the first bale it will cut the twine then you can remove the remaining bit of twine with the knot you tied.
How do you set the timing on Massey Ferguson 12 hay baler?
first your two roll in their compartment,run under the little plate before exiting and then going thru the two tension aid springs and then both thru the 1st porcelain,then divide for each porcelain on needle and go tie at base of needle and then engage manually for tiyng knot and then rotate whole system by hand by turning the flywheel. Gidday, I am self-taught on the 503, but after threading the needle, I pass the twine straight up through the gap in the knotting mechanism, against the thingy with the multiple serrated discs, then tie it back to the bale density adjuster at the back. After the first bale it will cut the twine then you can remove the remaining bit of twine with the knot you tied.
Is chris Massey and kyle Massey brothers?
yes, because they look and talk like each other
How do you change the screens on a Massey Ferguson grinder mixer model 15?
Open the mill and remove and replace the screen. You shouldn't need any tools as the mill lid is held in place by a couple of t-bolts - one on each side.
How do you you thread a new holland 310 hay baler?
Place two rolls of twine into the twine chamber, pull the end of the twine from the center of the rolls. Thread the twine from each roll through the loops in the lid of the twine chamber. Each twine should go through the loop on the side of the lid that the roll of twine sits on. The left side through the left loop, the twine on the right side through the right side loop. Run the twine through the two tubes on the left side of the twine chamber. The again, the left through the left side, the right through the right side. Close the lid to the twine chamber. Run the ends of the twine through the porcelian electric insulator fastened to the needle carriage, then the ends of the twine through the eyes of the needles. Again, the twine from the left side through the left needle eye, the end of the twine from the right side through the eye of the right needle. Pull the ends back to the protective pipes surrounding the needles and tie the ends to the pipe. Raise the bale trip lever on the drivers side of the bale chamber so it will trip shortly after you power the baler. You will need a small amount of hay going through the chamber to do this. When the bale trip lever trips, the needles will come up and the knotters will grab the twine and hold it. You are now ready to bale.
How do you thread a McCormick IH Forty Six baler?
THREADING THE TYING MECHANISM for a McCormick No. 46 Baler Open the door on the twine chest and place balls of twine in twine containers. There is room for 4 balls, 2 for each side. From left to right, as you look from the back of the baler, they will be referred to as balls D, C, B & A. Connect the inside end of ball "A" to the outside end of ball "B" connecting the two balls of twine in the right twine container. Connect the inside end of ball "C" to the outside end of ball "D" connecting the two balls of twine in the left twine container. If twine is taken from the wrong end of a ball, it will twist and snarl in the tying mechanism. Join the twine ends with a firm square knot. Trim the loose ends about one-half inch from the knot and you're ready to thread the tying mechanism. Make sure the needles are in their extreme rearward position. If they are not, turn the flywheel and power take-off drive by hand until the needles reach the extreme position of their rearward stroke Thread the twine from the inside of ball "B" through the grommet in the right partition and the center guide in the top of the left compartment of the twine chest. Thread the twine from the inside of ball "D" through the lower guide in the left compartment of the twine chest. Thread the twine balls "B" and "D" through the grommet in the left partition of the twine chest. Thread the twine between the pressure plates of the twine tension device and through the grommet in the bottom of the twine chest. Run the twine through the twine guide on the needle tie pipe and through the three twine guides underneath the bale chamber. The twine from the right twine container furnishes twine for the right needle and the twine from the left twine container furnishes twine for the left needle. Thread the ends of the twine through the holes of the needle head. Pull these two twine ends up through the bale chamber. Operate the baler slowly under power. Hold the twine as shown in Illust. llA (I tie it off to something near the back of the baler). Trip the clutch, and let the tying mechanism go through a cycle. Strip the single knots off the knotter hooks to complete the threading operation. Operate the tying mechanism several times at rated engine speed to be sure it is working smoothly. Hold the twine by hand each time to prevent the twine from fouling in the knotters.
How do you thread international 430 hay baler?
Twine comes out of the twine box, through the tensioner, through a couple of ceramic rings then 1 piece of twine through each needle eye. Once through the needle eye it goes back along the chamber floor and tie it off to something sturdy. The baler will thread the twine into the knotters at the first cycle. A common problem on old balers is the needle eyes have grooves warn in them. You should use a round file to file out the groove so the twine has a smooth surface to run over. A rough surface will cut the twine.
How do you thread a john deere 336 wire baler?
Threading the WirePlace a box of twine or wire in each of the two holding brackets at the rear of the baler. Remove the cardboard discs in the center of each box and locate the end of the twine or wire on the inside of the coil.2Pass the end of the twine or wire from the right-hand box through the ceramic spool on the right-hand side of the ejection chute.3Pass the end of the twine or wire into the bottom opening of the right-hand threading needle. Pull the twine or wire out through the top of the needle.4Pull the twine or wire taut and tie it securely to the eyebolt, just ahead of the right-hand threading needle.5Repeat the procedure for the left-hand threading needle.If the twine or wire snaps when you engage the baler, you may have gotten the loose end from the outside of the coil instead of the inside. Check to ensure that the end of the twine or wire does not pass under or into the coil inside the box.- If the wire snaps, you started the wrong end from the box of wire. Pay attention to the "Start this end" tag.
What are the names of each member of the Black Eyed Peas?
williamElephunk Fergie Stacy Ferguson
Is there a Parts cross reference list for Massey Ferguson to perkins?
You may want to check with a third party source to see, depending on what parts you need. I'm thinking someplace like NAPA or other Auto Parts catalogs might show some of the same for each and quite often they would list them together. Or, if you know the Perkins model you could get a manual for that engine. It's probably the same, although Perkins may have changed something for Massey Ferguson. As an example, they may have changed motor mounts, or fuel lines, air intakes, or similar so they would adapt to MF's tractor easier. You should be able to find a Perkins manual on Ebay or a similar web site.
What does Craig Ferguson throw at the camera man each night on his show?
candy gold coins
How much money does kyle Massey make?
200k per episode of thats so raven, 100k for each episode on his own show.
