0
On 209 primer conversion kit should the new breech plug screw in as far as the old one?
Wiki User
∙ 15y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you replace primer ball to gas tankto my McCulloch chainsaw mac3200?
It is simply held in by plastic tabs on the primer bulb. All you have to do is pry behind it and easily pop it out with a flat screw driver.The tabs break easily but replacment primer bulbs are available.http://store.chainsawr.com/
Where do fuel line go on poulan chainsaw?
byrumjr the line starts with the fuel filter in the tank and travels up to the carburetor out of the carburetor into the primer bulb, out of the primer bulb back in the tank raylago fuel line routing is as follows for all 2 cycle with primer ball external to the carb. remember the fuel is sucked into the carb, not puished or blown into the carb. the filtered line from the fuel tank goes to the "in" side of the carb. this is usually right next to the high speed adjustment screw on a walbro carb. the "out" line from the carb goes to the suction side of the primer ball, the output of the primer ball goes back to the return line in the fuel tank. if you have to run the choke and the carb high speed screw will not adjust properly, reverse the in and out lines to the carb.
How does the number of threads on a screw affect the distance the screw moves?
the threads determine the depth the screw should move
How do you disassemble a marlin mls-50?
remove the 2 bolts for the stock and then the 2 bolts that hold the trigger onto the barrel. Remove the large cap on the back of the barrel with a large screw driver. Be careful to hold it in place when removing it because it is under spring pressure. Once removed, remove the firing pin, cap, and two springs. Then cocking lever should be loose now so it will come out. You can now use the breech tool to remove the nipple and breech plug. reverse to assemble.
How do you disassemble a marlin MLS 50 muzzleloader?
remove the 2 bolts for the stock and then the 2 bolts that hold the trigger onto the barrel. Remove the large cap on the back of the barrel with a large screw driver. Be careful to hold it in place when removing it because it is under spring pressure. Once removed, remove the firing pin, cap, and two springs. Then cocking lever should be loose now so it will come out. You can now use the breech tool to remove the nipple and breech plug. reverse to assemble.
How do you disassemble a marlin MLS-50 muzzleloader?
remove the 2 bolts for the stock and then the 2 bolts that hold the trigger onto the barrel. Remove the large cap on the back of the barrel with a large screw driver. Be careful to hold it in place when removing it because it is under spring pressure. Once removed, remove the firing pin, cap, and two springs. Then cocking lever should be loose now so it will come out. You can now use the breech tool to remove the nipple and breech plug. reverse to assemble.
What should someone do when they step on a screw?
Yell
I have a 49cc X7 2 stroke super pocket bike how do you get fuel to the carb it appears that it will only run off of the fuel from the primer runs 10-20 seconds and cuts off any help?
hi, if you can get fuel to the primer from the tank then your problem is in your carb.there's a screw on the side of the carb screw it all the way in then turn it in the opposite direction about 2-1/2 full turns if this works you can fine tune the carb by holding the throttle wide open with bike running and slowly turning that screw until the engine revs as high as possible.if this doesnt work then your carb needs to be cleaned
How can you reduce friction on a screw?
There are several methods that you can use to reduce friction a screw. The guide collar of the screwdriver should be in an angular position in relation to the screw. This will ensure that the screw goes in a linear motion and reduces friction.
How do you convert model 44 Stevens to center fire?
The breech block has to be bored out for a bushing. Then the block is threaded. I screw in a hardened steel bushing with a hole in it for a centerfire firing pin. The bushing and the firing pin have to be custom made as I know of no supply of such bushings.
How do you clean a 30-30 Marlin Model 200-h lever action from the muzzle end?
It's always best to clean from the breech end, but if you want to clean from the muzzle end, simply open the bolt, and then run your cleaning rod down the muzzle. Might be a good idea to put a piece of old rag in the bolt opening so the debis that is pushed out, wont end up in the action. Marlins are very easy to clean from the breech end. Simply open the lever half way, pull the lever screw, remove the lever, then pull the breechbolt out. You can now clean from the breech end.
Should i screw your nan?
Capitalize your 'I'. I have no idea what you're talking about.
