0
You can buy a relatively inexpensive puller for that at most auto parts stores.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How to remove crank pulley?
On most newer cars, the crank pulley is one piece with the harmonic balancer.... Remove it with a harmonic balancer puller.
How to remove a harmonic balancer from a 350?
you should use a tool called a harmonic balance puller. the balancer came off in two pieces and the second piece that's still on the crank shaft won't come off
Does a harmonic balancer knock when it goes bad on a 305 Chevy?
The balancer is made of 2 pieces That have a rubber piece in the center of them that hold the balancer together. If the balancer comes apart YES it will knock / make noise and the engine would vibrate/shake. You would be able to move 1 piece of the balancer with your hand if that was the case. Check it.
Can a harmonic puller also install a balancer?
Not that I know of. I use a piece of threaded rod that fits into the crank along with a few heavy duty flat washers and a nut to draw the balancer in.
What would cause a harmonic balancer to shimmy on a 350 Chevy engine?
The balancer has a piece of rubber that holds it together, The balancer is made of two pieces with rubber in the middle, and the rubber is coming apart. REPLACE BALANCER. The Pulley that's bolted on the balancer may be bent or not on stright and flush on the balancer, That would make the balancer look like its wobbleing too.
Is the main crankshaft pulley one solid piece?
In most cases no, it is two pieces pressed together with rubbber in between. It is called the vibration damper or the harmonic balancer.
How do you install a harmonic balancer on a small block Chevy engine?
Slide the balancer on the crankshaft snout as far as you can by hand, then put a harmonic balancer installation tool in and crank it down until it bottoms out. If you can't afford to buy the tool, you can make one with a piece of 1/2-20 threaded rod, a nut, and some big thick washers. Put grease between the washers so they will slip easily while you're tightening the nut.
Harmonic balancer on a 1996 Chevy s 10 blazer do they warp?
No they do not. If you look at it real close you will see that it has a piece of rubber between the 2 steel parts that make the balancer, the rubber has sliped / worn out. The balancer is made of 2 pieces of steel with rubber in between them. REPLACE BALANCER. Before you take it apart make sure that the pulley that is bolted to it is not on crooked are bent. May just need a pulley put on it.
Remove harmonic balancer on a vs commodore?
You Will Need Breaker Bar, 15/16 socket or metric equivalent, piece of pipe to increase length of breaker bar. Remove the fuel pump fuse Place socket on big bolt in the centre on Harmonic Balancer with the Bar and pipe on top on the passenger side chassis rail. Turn car over a few times, the nut should loosen. Remove Balancer with a claw puller or if you're lucky it may just wiggle off.
How do you remove harmonic balancer pulley 1996 ford tauarus?
to solve your problem you simply need to drive that piece straight off a cliff, however, it may take a few tries to get through the guard rail. but i did this and i have not had problems since.
There is no noise when accelerated but there is a knocking sound when the gas pedal is released the lower the gear the louder it is What is wrong with your car?
I had a 94 buick regal that did tis. It was a 250 dollar repair job. It was the piece that spins the power accessory belt on the engine. I think its called a harmonic balancer
How long can you drive your car with a bad harmonic balancer?
That's an odd question, first who told you the harmonic balancer was bad? Balancers are mounted on the crankshaft at the factory, and it is actually just a weight attached to the end of the crankshaft to offest the firing of the pistons producing a smoother running motor. Harmonic balancers do not go bad, EVER, unless they are removed and damaged during engine repair (unlikely, very unlikely). They can be re-installed incorrectly after major engine repair, or simply left off due to negligence on some cars after major engine repair but I have never heard of a balancer going bad, as it is not a part that can actually fail. Harmonic balancer is a fancy word for weight, however if it has been removed or severely damaged due to impact I would strongly suggest having it fixed immeadetly as the unbalance can actually warp the crankshaft at high speeds and destroy your engine. Hate to keep driving this point home but harmonic balancers do not go bad, you should seek out another mechanic to check out your car, if I were still a mechanic I would only have told someone that if I was trying to rip them off due to their lack of automotive knowledge, or get them away from my shop because they were annoying or a problematic customer. (sorry)
