0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do set the lifting pressure of boiler safety valve?
The lifting pressure is set by turning the adjusting nut on top of the valve.
P-trap replacement metal drain pipe from wall has swivel flange but missing slip nut. Is there a special way to still use this pipe as is with a new plastic or metal trap?
you can use a rubber connector with two "O"ring which are usually attached to the rubber. so you take rubber connection and slip it on the P tighting it and then do the same with the other side should work cost about $ 2.50
What is a retaining nut in plumbing?
A retaining nut could be the packing gland nut on a valve stem or the nut used on a flare or compression fitting
What is the difference between screw and nut?
A nut is called screw when its head is tightend in component .but in case, tight of nut is not possible without bolt.since screw is tight without nut bolt it is not possible in case of nut.
History evolution of nut hardware?
What is the history evolution of nut?
How do you replace rear wheel bearings on a 1991 Dynasty And how tight do you torque the wheel bearing nut?
you have to press it out and press the new one in just make sure you tighting it real good
Why is heat used to loosen a rusted nut on a bolt?
By heating the nut (and avoiding the bolt as much as possible) the metal expands, this increases the size of the hole in the middle, releasing pressure against the bolt and allowing you to turn the nut while hot. Wear heat proof gloves, eye protection and have extinguishing equipment and cold water to hand. The level of heat required is often described as "cherry red" and can cause some types of metal to permanently change their hardness... be very careful if you are working on safety critical things like brakes, replace all affected parts.
Where is the neutral safety switch on a 1996 Jeep?
the safety switch is on the passenger's side of the transmission. There is a rectangular shaft protruding through a 1" nut. The nut has a safety lock on it to prevent it from loosening. There are two bolts that mount the switch to the trans. The entire assembly is located just forward of the trans mount bracket, on the passenger's side of the trans.
How are cashews picked?
Its is important to remove a cashew nut from its shell, due to the fact that the cashew shell is in fact toxic. To remove the shell you must be wearing gloves to protect yourself from the poison. The nut itself is removed with a knife like tool.
Why does Vishnu wear so much gold?
She wore gold cause she is a hard nut
How do set the lifting pressure of boiler safety valve?
The lifting pressure is set by turning the adjusting nut on top of the valve.
What type of clothing do people in Washington state wear?
Not to be mean but that's a silly question. They wear the same clothes as anyone else in this world.
What did nut the goddess wear?
Goddess of the sky. Nut is a daughter of Shu and Tefnut. Her brother and husband is Geb. She had four or five children: Osiris, Set, Isis, Nephthys, and-in early Egyptian sources-Horus.
What are the best type of goalie gloves?
It is a matter of opinion. I have seen some nice gloves like the Cutters Yin Yang X40 Receiver Gloves or the Nike Vapor Jet 2.0 Receiver Gloves. They are both sharp gloves, but like I said it is a matter of opinion. You might be able to find a pair of sick nasty ill bed-ridden pair of gloves.
What did nut the Egyptian goddess wear?
Goddess of the sky. Nut is a daughter of Shu and Tefnut. Her brother and husband is Geb. She had four or five children: Osiris, Set, Isis, Nephthys, and-in early Egyptian sources-Horus.
Do axle splines go bad?
If the nut isn't tight on the end of the axle, the splines on the axle, in the hub or both can wear out.
What is the correct step by step procedure for arming the M49A1 trip flare?
insert safety pin, cut the wire, unscrew the nut, remove device
