0
Should the needle be Up or Down when finished stitching a seam?
Wiki User
∙ 11y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you get nice sharp corners when turning two sewn pieces of fabric together?
Well, the obvious answer is to stitch right to the corner and stop with the needle down in the fabric, pick the presser foot up and pivot the fabrics 90 degrees then continue stitching. When the seam is finished, clip the corner off and turn the fabrics right side out. BUT, THIS WILL NOT GIVE YOU A NICE SHARP CORNER! The correct way to do it is to stop stitching with the needle down in the fabric just before reaching the corner, pick the presser foot up and pivot the fabrics 45 degrees and take 2 stitches that are 1 mm long (yes, you have to adjust the stitch length). Stop with the needle down in the fabric and pivot the fabrics another 45 degrees. Be sure to readjust your stitch length and continue stitching. When the seam is finished, clip the corner off and turn the fabric right side out. The "rule" to remember that stitching a sharp corner will result in a blunt corner, but stitching a blunt corner will turn perfectly square. Practice this on scraps by using a thin leaded pencil to mark your stitching lines so you'll know exactly where you'll need to stop for the corners.
Why does your needle keep breaking when you free motion quilt on your Designer SE?
The most common cause of needle breaks while free-motion quilting is moving the fabric while the needle is still in the fabric. This is a very fine line, and only improves with practice. Usually directions will tell you to stitch at a very fast speed. However, I find that fast stitching doesn't give the machine time to make a good stitch. It might look good on the right side, but look at the underneath side and you'll usually see that the bobbin thread is laying on the fabric and is just looped around the top thread. If that's what you're seeing you can bet that the stitching will not be there very long. My method of choice is to set the machine for free-motion stitching by only lowering the feed-teeth. I use the little metal foot that looks like a horseshoe, it requires removing the ankle and attaches with the screw. As you stitch, it should move up and down with the needle. When the needle goes down, the foot goes down to hold the fabric for the stitch to form. Generally, I'll use a titanium needle because they stay sharper longer. I also set the speed to the slowest or one click up. Keep your foot on the foot control, but you're not going to use it to stitch. When you're ready to begin stitching, touch the "start" button and let the machine go at it's own pace. It will start slow, but picks up speed after just a few stitches. When you want to stop, just tap the foot control and it will stop stitching. Be sure your needle is set to stop in the down position. I have used this method for years -- I love whoever put the automatic stitching and speed controls on the Vikings! I've also taught many classes and the ladies were successful with the free-motion. Practice, practice, practice!!
Should a needle be inserted bevel up or down?
Always bevel up.
Should a needle be inserted with bevel up or down?
Always bevel up.
What should you not do on a sewing machine?
you shouldn't put your finger underneath the needle when its going up and down.
What is the motion of a needle of a sewing machine?
The motion of the needle in a sewing machine is vertically, rapidly up and down.
Why needle sinks down?
cause
How long would it take to chop down a full sized pine tree with a knitting needle?
You cannot chop a tree down with a knitting needle as the needle does not have a sharp edge. You could bore it down if you lived long enough.
Which way should the bevel of the needle be held when performing venipuncture?
When inserting a needle, the needle is inserted bevel up.However, at least 1 study suggests (in the same article) that bevel down may help on difficult sticks, on pediatric or dehydrated adults.
What is the meaning of needle clamp?
The needle clamp is collar and screw device that holds the needle to the needle bar. The needle bar is the part that goes up and down as the machine sews and is in front of the pressed foot bar.
What is the automatic bobbin winder?
Automatic declutch bobbin winder – which means the machine automatically stops the needle from going up and down when you are winding thread onto the bobbin. ... Needle up/down button – this button allows you to start and stop with the needle in the down position if it is highlighted.
What is needle bar?
The needle bar is a component of a sewing machine that holds the needle in place and controls its up and down movement. It is connected to the machine's mechanism that creates the stitch by moving the needle in synchronization with the fabric being sewn.
