disconnect the negative battery cable then the wires from the starter. Remove the mounting bolts and drop the starter down. Try this for Chev S10 problems. Buy the Chilton General Motors publication #28860. It covers S10s 1982-93 from detailing to engine rebuilds, including changing the starter.
Add your answer:
Related Questions
How do you replace a starter on a 2000 Cavalier?
Disconnect the - battery cable Raise and support vehicle Disconnect wiring harness at the top of starter Remove starter mounting bolts Twist starter to remove
Would a starter from a 2000 2.4 cavalier fit a 2001 2.2 cavalier?
No...The bolt mounting hole are different...the 2.2 bolts will cross the starter in a "T" fashion and the 2.4 bolts will go in a line "with" the starter. They have different part numbers at the store as well....
How many bolts in 2000 Mercury Sable starter?
The 2000 Mercury Sable starter will have three retaining bolts. There will be two cable retaining nuts on the front of the starter.
How do you replace starter on 3.3L 2000 Dodge Grand Caravan?
Disconnec battery Starter is located under car where engine meets tranny, remove the electric connectors Remove starter mounting bolts Install new starter in reverse order of removal
How do you get the caliper off a 2000 suburban?
Should be 2 mounting bolts at the rear of caliper
How do you replace thermostat housing in 2000 S10?
Remove 2 mounting bolts and replace
Where are the mounting bolts for front calipers on a 2000 Tacoma truck?
On the inboard side of the caliper.
Where is the starter on the Chevy 2000 Chevy Blazer?
The starter motor/solenoid on a 2000 Chevy S10 Blazer is on the lower passenger side of the engine block. If your trying to replace it, first, disconnect the negative battery terminal. Remove the differential carrier shield. Disconnect the bolted solenoid cables. Remove 2 vertical bolts securing the starter motor to the engine block. When reinstalling starter, tighten mounting bolts to 50 Nm/37 lb. ft.
How hard is to change a starter on a 2000 Nissan maxima?
* Disconnect the negative battery cable * Remove the air intake duct and the air cleaner housing assembly from the engine compartment * Disconnect the battery cable and the solenoid terminal connection from the starter solenoid * Remove the starter motor mounting bolts and detach the starter from the engine
How do you replace a starter on a 2000 Saturn SL1 sedan 1.9l and how many bolts hold it on?
Remove the positive battery cable from your 2000 Saturn battery. Remove the cables from the front of the starter. Remove the three starter retaining bolts. Reverse the process to install the new starter.
How many bolts do hold the starter on 2000 infiniti i30?
3
How to change starter on 2000 LEXUS rx 300?
Remove your battery. Remove the battery tray. Remove the air filter housing and air intake duct. Remove the starter motor mounting bolts. Pull the starter away from the engine a bit. Detach the electrical connector from the starter solenoid. Remove the nut and disconnect the battery starter cable. Remove the starter and put in your new one.
How do you replace the starter on a 2000 Nissan Altima?
The starter is located beneath the throttle body. Remove the intake tube, then the starter bolts can be removed and the starter replaced.
What is the torque specs for the brake caliper mounting bolts on a 2000 buick lesabre?
75 ft lbs
How do you install a 2000 Yamaha waverunner XL 1200 starter?
To install a 2000 Yamaha Waverunner XL 1200 starter, first remove the 2 bolts. Then the wires connected to the starter. Remove the starter and replace with new.
How do you replace bad starter on 2000 Grand Prix?
its a bit tough but first disconnect the battery.then jack the car up safely.after that remove the two starter mounting bolts and pull the starter out slowly.then unbolt the wires at the starter when the starter is hanging by the wires(carefully)remove the starter and reverse the steps to reinstall the starter and reconnect the battery Here's a writeup on the process. http://hubpages.com/hub/Starter-Removal-1999-Pontiac-Grand-Prix
How do you install lower control arm in 2000 suzuki esteem?
Locate the control arm under the vehicle. Attach it with mounting bolts. Put the bushings in place. Tighten the mounting bolts only when all bolts are installed. Connect the sway bar the lower control arm.
How do you change the starter on a 2000 Chevy Malibu?
Remove the positive battery cable from your 2000 Chevy Malibu battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.
How do you change a 2000 Isuzu Rodeo starter?
remove the starter bolts your 12v power supply and ignition wire then remove exhaust bolts from manifold a few twist and turns and out she comes
What is the torque specs for the brake caliper mounting bolts on a 2000 mercury villager?
18-25 ft lbs.
How do you change a starter on a 2000 ford escort?
To change the starter do these steps: 1. Remove the negative battery termnal off the battery. 2. Take the battery and tray out of the engine bay. 3. Take the big positive battery cable off of the starter. 4. Take the small s terminal off the solenoid. 5. Take the upper mounting bolt loose with a ratchet, extension and socket. 6. Take the 2 lower mounting bolts loose. 7. Lift the starter up and out of the engine bay.
Where is the starter located on a 2000 Hyundai Elantra?
The starter on a 2000 Hyundai Elantra is located along the bottom, left side of the engine. It bolts directly to the engine block and is protected by a shroud.
Where is the starter on 2000 Chevy Silverado Z71?
Mine (5.3L) is on the PASSENGER side underneath the engine. It has 2 bolts mounting it to the block and 2 wires on the solenoid (battery and ignition). Once you remove the two long mounting bolts, you can wiggle it towards the front of the vehicle to remove it (it takes some doing). Remember to disconnect your battery first to prevent any shorts. Battery side of engine low on the engine.
Where is the starter located on a 2000 Nissan Maxima?
The starter on a 2000 Maxima (V6) is located under the battery. Follow the positive charge size wires down to 2 17 millimeter bolts.
How do you remove brake caliper on a 2000 Buick LaSabre?
Two mounting bolts at rear of caliper - then slide caliper off rotor
