answersLogoWhite
Ford Ranger
Chevy Malibu
Chevy S-10
Thermostats

How do you replace thermostat housing in 2000 S10?

272829

Top Answer
User Avatar
Wiki User
Answered
2007-05-13 22:31:09
2007-05-13 22:31:09

Remove 2 mounting bolts and replace

001
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


replace the coolant sensor, the one next to the thermostat housing.


Replace the coolant temp sensor next to the thermostat housing.


Follow the upper radiator hose to the engine. The hose is attached to the thermostat housing. Remove the thermostat housing to expose the thermostat.


Follow the upper radiator hose from the radiator to the engine. It is attached to the thermostat housing. Removing the thermostat housing will expose the thermostat.


With engine cool, drain off aprox 2 qts of coolant from the radiator, remove upper radiator hose from thermostat housing, remove thermostat housing, remove thermostat and seal, reverse order to install, make sure thermostat spring is facing into the engine.




If you follow the upper radiator hose to the engine, the hose is attached to the thermostst housing. The thermostat is located under the thermostat housing.


Follow the upper radiator hose from the radiator towards the engine. The upper radiator hose is connected to the thermostat housing on the engine side. The thermostat is under/inside the thermostat housing. Remove the upper radiator hose from the housing then remove the two bolts holding down the thermostat housing then remove the thermostat housing to expose the thermostat.


The thermostat is under the housing that the top radiator hose connects to, remove the hose then the housing and change the thermostat. The bolts are metric so be prepared with the proper tools.


Follow the upper radiator hose to the engine, the thermostat is under the housing the hose connects to.


It is under the thermostat housing located at the engine end of the upper radiator hose.


It is on the cylinder head near the thermostat housing.


Follow the upper radiator hose back towards the engine. The hose will be connected to the thermostat housing. The thermostat is under the housing. Drain off some colant, remove upper hose from thermostat housing, remove the two bolts holding the housing to the engine, remove the housing, remove the thermostat, take note that the thermostat spring faces the engine so as not to install backwards.


It is under the housing where the upper radiator hose hooks to the engine.


Rule of thumb, follow upper radiator hose from radiator towards engine. This should lead to the thermostat housing.


It is at the end of your top radiator hose where it clamps onto a housing on the engine. It is under that housing.


Replace the coolant temp sensor, the one next to the thermostat housing.


Should be located in a removable housing at the engine end of the upper radiator hose Drain about 1 gallon of coolant frm the radiator Remove this housing Note how thermostat is installed Clean both surfaces Replace thermostat and gasket Replace housing Re-fill coolant slowly to prevent an air lock Start engine and look for leaks Run engine to normal operating temperature with heater on Re-check coolant level


If it has a 4.3L engine the temp sensor is located next to the thermostat housing.


Get a Haynes repair manual for your 2000 Chevrolet S10. Covers most minor service questions like this. Any Autopart store. $17 or $20.


It is in the intake manifold near the thermostat housing. It is the one with the yellow and black wires.


The temp sensor for the ECM (engine control module) is next to the thermostat housing.


The one the ecm reads is located right next to the thermostat housing.


I've got a better question, why is this question in the Chevy venture forum ?



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.