0
Might try putting an air gun on the crank pulley nut but not recommended. Best to replace the starter motor and do it right
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you start a motor without a starter?
By the use of auto transformer and bridge rectifier we can start dc motor.
What happend when you start motor without starter?
The windings of the motor will be gonebecause of high current diectly goes to the windings of motor.
If your automatic car thinks it is gear and so the starter motor wont start how do you correct this?
Align the neutral lockout switch.
What is a three point starter?
A three point starter is a device that is meant to help start a DC motor. A three point starter will start device without much starting current.
Why wont my 1985 5 speed fiero start without a pushstart?
Bad starter motor?
How does vehicle start?
it start by starter motor
What does a car starter motor solenoid do?
When opened by the starter switch, it sends electricity from the battery to the starter motor to start the car.
Where is 1.7 automatic starter motor?
that is in front of the car where all of the engine and battery is
How do you remove a starter from a 1976 Ford Granada 302ci automatic transmission?
take right side motor mount loose and jack motor up to get starter off.
How do change the starter on a 2000 Dodge Durango?
== # Disconnect and isolate the battery negative cable. # Raise and support the vehicle. # Remove the nut and the lock washer that secures the lower mounting flange of the starter motor to the stud on the automatic transmission torque converter housing # While supporting the starter motor with one hand, use the other hand to remove the screw and washer that secures the upper mounting flange of the starter motor to the automatic transmission torque converter housing. # Slide the automatic transmission cooler tube bracket forward on the tubes far enough for the starter motor mounting flange to be removed from the lower mounting stud. # Lower the starter motor from the front of the automatic transmission torque converter housing far enough to access and remove the nut that secures the battery positive cable eyelet terminal to the starter solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Remove the battery positive cable eyelet terminal from the solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Disconnect the battery positive cable solenoid terminal wire harness connector from the connector receptacle on the starter solenoid. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Remove the starter motor from the automatic transmission torque converter housing. == # Disconnect and isolate the battery negative cable. # Raise and support the vehicle. # Remove the screw and washer (rearward facing) that secures the lower mounting flange of the starter motor to the automatic transmission torque converter housing # While supporting the starter motor with one hand, use the other hand to remove the screw and washer (rearward facing) that secures the upper mounting flange of the starter motor to the automatic transmission torque converter housing. # Lower the starter motor from the front of the automatic transmission torque converter housing far enough to access and remove the nut that secures the battery positive cable eyelet terminal to the starter solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Remove the battery positive cable eyelet terminal from the solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Disconnect the battery positive cable solenoid terminal wire harness connector from the connector receptacle on the starter solenoid. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Remove the starter motor from the automatic transmission torque converter housing. == == # Position the starter motor to the automatic transmission torque converter housing. # Reconnect the battery positive cable solenoid terminal wire harness connector to the connector receptacle on the starter solenoid. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Install the battery positive cable eyelet terminal onto the solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Install and tighten the nut that secures the battery positive cable eyelet terminal to the starter solenoid B(+) terminal stud. Tighten the nut to 13.6 N·m (120 in. lbs.) Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Position the hole in the starter motor lower mounting flange over the stud on the automatic transmission torque converter housing. # Slide the automatic transmission cooler tube bracket rearward on the tubes and into position over the starter motor upper mounting flange. # Loosely install the screw and washer unit that secures the starter motor upper mounting flange to the automatic transmission torque converter housing. # Loosely install the lock washer and nut that secures the starter motor lower mounting flange to the stud on the automatic transmission torque converter housing. # Tighten the screw and washer unit and the nut that secure the starter motor mounting flange to the automatic transmission torque converter housing. Tighten the screw and the nut to 67.8 N·m (50 ft. lbs.) # Lower the vehicle. # Reconnect the battery negative cable. == # Position the starter motor to the automatic transmission torque converter housing. # Reconnect the battery positive cable solenoid terminal wire harness connector to the connector receptacle on the starter solenoid. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Install the battery positive cable eyelet terminal onto the solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Install and tighten the nut that secures the battery positive cable eyelet terminal to the starter solenoid B(+) terminal stud. Tighten the nut to 13.6 N·m (120 in. lbs.) Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Position the starter motor mounting flange on the automatic transmission torque converter housing and loosely install the two screw and washer units to secure it. # Tighten the two screw and washer units that secure the starter motor mounting flange to the automatic transmission torque converter housing. Tighten the screws to 67.8 N·m (50 ft. lbs.) # Lower the vehicle. # Reconnect the battery negative cable.
How do you start single phase induction motor?
capacitive start motors start by themselves however a normal single phase induction motor requires a starter motor to 'kick-start' the motor into action.
Engine will not start on citroen despatch?
check starter motor
