0
The power brick is fine but when i push the button to turn on Xbox no green or red lights come on the consol but the Xbox turns on the visual and audio work but the controllers wont connect either?
Wiki User
∙ 14y ago
Most likely will need sent in for repairs. Call 1-8004MYXBOX
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you get past the select wifi screen on your nexus 7?
Either hit the back button or choose the network you want to connect to.
Can you turn off your wii REMOTE control?
Usually it turns off after you turn off the Wii, but if you accidentally turn on extra controllers while playing, you can just pop the back cover open and pull a battery out of place. Either that, or you can go to the Home screen, disconnect all controllers, and only connect the ones you want to use.
Are the PS3 controllers Bluetooth or RF?
you can get either blue tooth or RF
How many Xbox controllers can you use at once?
Four controllers can be connected either wired or wirelessly to one console. Each console can only support up to four or fewer controllers at one time.
Are there controllers for Kinect?
yes, you can either use one, or dont use one
What does WPS means which is printed on ptcl router model KW5815?
WPS or WiFi Protected Setup is used to connect to your wireless AP. It has 2 methods one is WPS button and second is WPS pin. 1. WPS Button (usage): When you try to connect an "Wireless Access point" a dialouge box comes up asks for the Password that should be entered in order to connect to the "wireless AP". At this stage you can either enter the password or you can use WPS button. while the password dialouge box is open. in windows 7 "Connect to a Network" dialouge box says "You can also connect by pushing the button on the router". if you don't want to connect with AP by entering password you can push the "WPS Button" on your "PTCL" device. and there you go, you are connected to your WiFi.. :) 2. WPS PIN (usage): NOTE: make sure your PIN is active in the settings of your PTCL device!
How do you program an Xbox controller?
this answer is for a wireless controller. there is a button to the left of where you plug in wired controllers. you click that button and the power button of your xbox will start blinking. then you take your wireless controller and there is a small button above the box where you put the batteries in that you have to click and wait until your controller stops flashing and shows that either player 1, 2, 3, or 4 is connected.
Do you have to buy multiplayer on PS3?
Sort of. If you want online multiplayer you need to buy an internet connection and the hardware to connect it. If you just want to play with a few friends at your house you need to purchase both a game with that capability and more controllers as the PS3 only comes with one. It either case the PS3 could do it without you buying something if you already had the internet connection controllers and games
How do you button your three button suit?
Either button two only, or all buttons.
How do you turn on guitar hero red octane cotroller I can not find an on off button as mentioed on the activision help line?
For all guitar hero and rock band guitars, drum kirts, and normal controllers the main 'on and off' button is the xbox 360 symbol button, You hold it in to turn it on and it automatically turns off. If this is the first time, you will need to sync the relative controller to the console. To do this press the small circular button located under the disc tray, accross from the memory card slots on the xbox 360's face plate, this should send a ring of light around the xbox 360, whilst at this moment, press the same button located on either of the controllers which is usually a smaller circular button with a little radar signal next to it similar to on the xbox! Hope this helped
You can click either the view button or the button on the ribbon to execute the query?
Run button
How do you install an ignition button for under the hood diagnostics on a 1992 Chevrolet 1500 Truck?
Buy a push button from an auto or tractor parts store, mount it in the desired location, and route two 12 guage wires from the button to the starter. Connect one wire to the large, center post on the solenoid and touch the other wire to either of the other two posts on the solenoid while pushing on the starter button. When the engine starts cranking, you'll know which post to connect the other wire to. Connect the wire to the correct solenoid post, and then check the wire routing to avoid major heat sources that might damage the wires.
