Toyota Trucks and SUVs
Torque specs for 1991 Toyota pickup v6 4x4 pressure plate?
Wiki User
2012-01-08 23:47:56
Haynes Auto Repair Manual say's
Clutch pressure plate-to-flywheel Torque should be 11 to 15
Ft-LBS
Hope that helps....
Related Questions
Asked in Toyota
What are the torque specs for 1985 Toyota 22R flywheel bolts and pressure plate bolts?
80Lbs for flywheel, 10 to 15lbs for pressure plate
Asked in Suzuki Samurai
What is the torque specs for the pressure plate on a suzuki samurai?
Pressure plate to flywheel torque is (ft lbs) 14 to 20.
Asked in Auto Parts and Repairs, Suzuki Samurai
What are the torque specs for the pressure plate on a suzuki samurai?
Pressure plate to flywheel torque is (ft lbs) 14 to 20.
Asked in Chevy S-10
What is the torque setting for a 95 s10 2.2 pressure plate bolts?
The torque setting for the pressure plate on the clutch for an
s10 2.2 is 33 foot pounds. The torque for the 4.3 is 29 foot
pounds.
Asked in Detroit
What is the torque spec for the pressure plate bolts on a 12.7l 60 series detroit?
Torque specs pressure plate to fly wheel 60 series Detroit
deisel
Asked in Clutches and Flywheels, Ford Ranger, Ford Bronco II
What are the Torque specifications for a clutch pressure plate on a 96 ford ranger?
pressure plate to flywheel bolts - 15 to 24
Asked in Clutches and Flywheels
What is the pressure plate and flywheel torque for a 1990 ford ranger?
Pressure plate to flywheel bolts - 24 ft/lbs
Asked in Clutches and Flywheels, Toyota
Which way is the clutch installed on a 1994 Toyota pickup which way do you face the springs on the clutch to the pressure plate or to the fly wheel?
Just make the clutch pads line up with the clutch disk. the
pressure plate can only go on one way due to the positioning
dowels
Asked in Kia Sephia
What is the torque specs for the clutch on a Kia Sephia?
whats the torque spec for the pressure plate on a 1998 kia
sportage?
Asked in Clutches and Flywheels
Flywheel torque specs for 71 Datsun 240z?
What are the torque specs for a flywheel and pressure plate on a
Datsun 240Z
Asked in Pontiac Fiero
Do you have to torque the bolts on your pressure plate for your 1986 Pontiac Fiero GT and if so at what lbs?
Yes, you have to torque everything on the drivetrain correctly.
The manual calls for 15 ft-lb (dry and clean) on the pressure
plate-to-flywheel bolts.
Asked in Chevy 350
Pressure plate torque specification for Chevy 350?
In 1970, the rating was 35ft/lbs.
Asked in Clutches and Flywheels, Chevy Camaro Z28
What are the torque specs for attaching a pressure plate to flywheel on a 1983 z28?
90 ft lbs is the standard torque on most flywheels
Asked in Toyota Trucks and SUVs
Where are the rear floor jacking points on a 1994 Toyota Pickup?
jack up on the rear axle or on the ubolt plate
Asked in Clutches and Flywheels, Ford Ranger, Mazda 3, Ford Ranger XLT
What is the torque specs for 2005 Mazda 3 flywheel and pressure plate?
Flywheel 79.7ft lbs - 85.5 ft lbs
pressure plate 18.5 - 24.4 ft lbs
Asked in Clutches and Flywheels, Honda Civic, Honda Civic DX
What are the torque specs for the pressure plate on a 93 Honda civic dx 15 liter non vtec?
The clutch pressure plate bolts are torqued down to 19 Ft
Lbs
Asked in Ford Falcon
What are the torque settings for an au 6-cylinder falcon with vct?
pressure plate torque settings for ford falcon au 6 cylinder
Asked in Clutches and Flywheels, Toyota
Replacement of Clutch on 87 Toyota 4WD Pickup?
Easiest thing for me is to remove the transmission first. Then
you can get to the pressure plate and the clutch. Its a simple
matter of a few bolts coming off. Remove the plate and then install
a new clutch and pressure plate. I would highly suggest you replace
the alignment bearing and the throw out bearing at the same time.
An alignment tool comes with most new kits for the plate. Us this
to line up the splines into the clutch plate and bearing.
Asked in Clutches and Flywheels, Nissan 300ZX
What are the Torque Specs on the Flywheel and pressure plate on a 1992 Nissan 300ZX non turbo?
For your 1992 Nissan/Datsun 300ZX: Flywheel Torque 61-69 Foot
pounds (Final torque)
Asked in Auto Racing, Ford F-150
What is the clutch cover bolts torque Specification on a 2001 Ford F-150 XL?
35 ~ 46 Foot pounds of torque. Pressure plate bolts.
Asked in Cars & Vehicles, Clutches and Flywheels
What is the torque spec for flywheel for Chevy S-10?
few websites i have searched have come back with a flywheel to
crankshaft torque spec of 50 ft-lbs same goes for the flex plate in
automatic models. pressure plate torque spec is 23 ft-lbs
Asked in Clutches and Flywheels, Dodge D100
How do you adjust the clutch on a 1985 custom deluxe pickup?
no adjustment on hydraulic clutch, worn clutch disc and pressure
plate
Asked in Dodge Laramie, DIY Projects
How do you change the clutch and pressure plate on 2002 2500 Dodge pickup?
Hire a professional mechanic, or buy a repair manual.
Asked in VW Beetle Type 1
What are the torque specs for attaching a pressure plate to flywheel on a 1997 volkswagen micro-bus?
refer to service manual
Asked in Chevy Blazer
What would cause a Knocking by the torque converter on a 1076 k5 blazer?
Loose converter bolts or a cracked pressure plate.