WHAT glue to use to glue 2 Cds together?
Super Glue or Krazy Glue would be best for that.
easy... just use super glue it will take 2 days to glue 4 tooth picks together
Yellow carpenter's glue and white glue.
i would suggest jet glue, or super glue, jet glue is avalible at hardware stores and super glue is available every where. Don't glue your fingers together! ANS 2 - Super glue is no god for shoe repairs ! -Use Goop Shoe Glue - in a tube, cheap, works great, available at most stores like Walmart, HD, Canadian Tire, etc
The best glue for balsa wood is contact adhesive. ANS 2 -the best glue for balsa wood is yellow carpenter's glue. Use pressure (a clamp) to hold it together at least 4 hours.
Not unless you have a transitional fitting. The diameters of the two are not the same. I know sometimes it can feel like they fit together snugly but they will not hold the pressure. ANS 2 - AS he says above, you can glue it but it's only usable for drainage, not regular water pressure. Use Weld-On 794 to glue it
The best way to glue popsicle sticks is to use a good PVA glue. TiteBond 2 or 3 if you have it is best. Elmer's white glue is reasonable and cheaper but also makes a similar joint for craft purposes.
Sand each piece ,,,,clean with alcohol,,then adhere with 100% clear silicone ANS 2 - Another alternative is to use the solvent glue required for that kind of 'plastic'.
Wood glue ANS 2 - I would use yellow carpenter's glue
no ANS 2 - Part of the point of pipe thread compound is to prevent surfaces sticking together.
if you have 2 ripcords cut them in half then super glue them together you can melt or glue them together but it will come off and break your launcher
I'm sorry, but it's not possible to make a glider that flies like Aang's, but it's possible to make something kind of like it. # Get a long, thin piece of wood a bit taller than you. # Get 3 pieces of poster board. # Aline 2 pieces of the poster board together. # Cut it out the shape of one wing wile the 2 are together. That way you will have 2 wings the… Read More
How can you make a Pyrus sword come out of your Bakugan gauntlet like on episode 27 from Bakugan New Vestroia?
You can tape 2 rulers together, color them red, and tape them to your gauntlet. You can also use super glue but don't expect it to come off if you do use super glue.
Make triangles (same length on all 3 sides), make 4 triangles and attach them, If you use paper, cardboard, or posterboard, you can lay them flat on a table and butt edges together, you will use 3 strips of tape to attach all 4 triangles, raise shape up to a pyramid form and tape last 2 edges together and there you have a pyramid. For a pyramid constructed of wood, the principal is the same… Read More
If it's a glass bottle super glue will work, but may have little strength.
Don't use Gorilla glue, you can make things worth. I had very good experience with www.denturerepairlab.com ANS 2 NO , you should not use gorilla glue on dentures.
by putting the glue on the wood and have both woods make contact ANS 2 - Super glue is far from effective on wood. Much better to glue any wood with a PVA type, white glue, yellow glue etc.
glue it together with pva glue then wait about 2 hours till it drys
Gorilla Glue ANS 2 - 'Gloozit' Plumbers Goop is better for that purpose.
The first product i recommend is Super Glue. Super Glue will be great with plastic and metal and most companies make products that are now easy to apply in small amount, saving your fingers. Polystyrene Glue. (commonly called plastic glue) This product is normally available in gel or liquid form. You should use this product with plastic ONLY. It melts the parts together in minutes. For big metal models, rare today, you can use Epoxy… Read More
It depends on the material that you try to glue together. You got to keep in mind that there's a lot of different glues and they have their own properties. So everytime you try to fix two materials together you need to make sure you use the right adhesive product. If you ask whats better between superglue and woodglue, I guess that you're trying to glue together wood. Then I have to answer to use… Read More
Contact cement. ANS 2 Contact cement will melt some foam surfaces ! - Use PL 300 in caulk tubes for best results
ANS 2 - Hot glue will burn your nails or skin . Do not do this.
If you are attempting to glue the 2 together for a small job I'd use a premium all purpose adhesive like PL Premium. If you are installing granite, or any other stone tile, I would use a proper tile setting mortar. ANS 2 - If it'a small job, epoxy will work but may be too expensive for something involving a lot of granite.
Any white glue will hold 2 popsicle sticks together quite well.
Crazy glue has always worked for me, I figured if it glues your fingers together it should glue leather. ANS 2 - 'Gloozit' Plumbers Goop works very well on leather.
takes 2 things and sticks them together!! ANS 2 -White glue works by being liquid enough to soak into porous surfaces, then hardens as it dries out.
super glue ANS 2 -If that's gluing a part that's critical to holding on, or steering you definitely should NOT only use Super glue. -At least find something rigid like a piece of metal pipe to 'splint' the broken part. -BE SAFE !
Bacarat Glass playing Dolphin and the nose has been broken off is there a special clear glue you could use to glue it back Thankyou?
Just use normal glue to try and there is a glue called RAZI if you can find it. It glues anything toghether even your fingers!:) ANS 2 -For this, I would use a very tiny drop of super glue.
Glue ANS 2 - An epoxy would be best for this.
I would personally say that stick glue does not hold up very well. But on the other hand a glue stick works well for glueing peices of paper together. But if are glueing bigger things like plastic to something i would use liquid glue!Hope this helps,WikiWooWhoLoctite 401 is the strongest genaral CA(superglue) in the market, has 1000kg of tensile stregth in 2 second.... nothing else comapares
PVA glue ANS 2 Epoxy or carpenters yellow glue may be best, depending exactly what you are gluing.
- PVA, white or yellow glue soaks into porous surfaces, then dries as it's carrier solvent evaporates. The substance left after evaporation has become hard and bonds the 2 surfaces together.
Gorilla glue ANS 2 - Epoxy will work and silicone will work.
yes they are put together with a glue, you use a cleaner first then apply glue to both sections and stick them together Ans 2 PVC pipe is commonly used for irrigation and similar projects. When assembling runs of pipe, each end should be coated with Weld-On P70 Primer, and after that dries with Weld-On 711 Adhesive, when sections are fitted together, they need to be held for about 2 minutes to set. Leave at… Read More
possible Tape is often used to hold the glued components in the correct positions while the glue cures, sets or otherwise bonds those pieces together. ANS 2 - There are many dissimilar things that cannot be easily and quickly glued together. Tape, in particular, duct tape and red 'Tuck' tape are very useful to attach things semi-permanently.
You can use a two-phase epoxy. Elmer's glue will work also. Hot glue is okay, but sets pretty fast. The purpose is to keep moisture out. ANS 2- I would use the best epoxy that I could get. This is a very critical joint and Elmer's or hot glue are definitely NOT recommended
To make a Rectangular Prism you should follow this 4 steps: 1) Draw a net for a rectangular Prism, including dimensions and glue flaps. 2) If you want you can name them (front, back, top, bottom, left side and right side) to make it easy for you. 3) Cut out your net, Dry fold, (fold it but don't glue the flaps), to be sure that it works. 4) If you are happy about the Rectangular… Read More
well i know that you have to use cornstarch to make goop but you dont have to use borax or glue ingridients 1.one cup cornstarch 2.1/2 cup of water (use on a 2:1 ratio)
What glue to use to glue 2 halves of matching same pieces of quartz no holes and perfect fitting together so it will stick?
Crazy glue does a good job. Make sure the broken surfaces are clean and dry. I like the gel form, you don't need much, but don't expect it to flow like the usual kind. Use as little as possible, and be prepared to deal with any excess. The stuff dries fast, and you can buy accellerants to speed it up too.
Silicone is more usually used as a sealant. But sure, as long as it sticks to the surfaces involved, you can glue stuff together with it. ANS 2 -MANY kinds of silicone are labelled as an adhesive.
You open up the gun, take out the bolt and soak it in hot water. The glue around the bolt will weaken and the bolt will split into 2 pieces and the air restrictor will fall out. The you simply glue the bolt back together with hobby glue and put it back in the gun and put it back together.
Have You Tryed Super Glue? ANS 2 - Super glue will NOT stretch when the rubber does, don't waste your time on it for this joint. -Liquid rubber glue as comes in bicycle tire patch kits is far better !
first dip it in water then get some super glue and stick it together and hold it together for 2 hours in front of a fan.Thats how I did it
super glue yay ANS 2 -Contrary to popular juvenile opinion, super glue is NOT always the answer. For shoes of any kind -"Gloozit' Shoe Goop is far better.
it is a glue used for gluing things together ANS 2 -Polyvinyl Acetate - the basic chemical component of white glues. Used for paper and cardboard and some light wood joints.
You might try a normal dryer sheet. ALL THE GLUES I USE (WOOD, 2-PART EPOXIES, WHITE, INSTANT, AND GORILLA GLUES, THE ODOR FROM THESE GLUES DISSIPATE THRU THE CURING PROCESS. IF ITS THE ODOR FROM THE GLUE WHEN YOUR GLUING THINGS TOGETHER, MOVE CLOSER TO A WINDOW AND PUT A FAN IN THE WINDOW TO EXHAUST THE ODOR.
im 15 and yes ANS 2 - Many schools use them
You will need A body (cardboard, egg carton, wood frame, ect.) 4 wheels (bottle caps, Lego wheels, CDs, ect.) 2 Pencils A rubber band Strong glue (super glue, hot glue, ect.) 2 Metal Washers (something similar to a washer will do) 1. Take something light, like a box, cardboard, or something along those lines. 2. Find 4 wheels, they can be store bought, bottle caps, Lego wheels, basically anything that could work. CDs work for… Read More
How can I replair my golf club when the head slipped off the shaft I put the head back on the shaft with no problems but the head shifts when I hit a golf ball. I was thinking of getting some glue.?
Use an abrasive on shaft and inside hosel, clean with acetone or alcohol, let dry, use 2 part epoxy on shaft and in hosel, join the 2 together, wipe off excess glue, allow to cure 24 hours before using.
Glues like the ones used at school are made up of long chains called polymers, which are a bit like spaghetti strands. When you glue 2 pieces of paper together the polymers get into all the microscopic cracks and crevices in the paper, (a bit like ink soaking into the porous surface of paper). As it dries and the water evaporates the polymer molecules are left in the cracks to hold the paper together. But… Read More