0
Check this Link may help http://www.hometips.com/content/frames_intro.html
Jamb liners(sides and head) and the sill.There is also the mullion(the centre vertical piece) if required,that divides the window sashes.If you are referring to the window sash,the parts are stiles(vertical side pieces) and rails(top and bottom horizontal pieces).
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How was the roller coaster built?
With all wooden parts.
How are houses so stable?
because they put all kinds of concrete and bricks as long as a wooden frame.
What measurement is used to measure the width of a window?
Windows are measured in the usual units of the country, whether metric (millimetres or metres) or imperial (feet and inches). The part of the window that is being measured needs to be specified. It could be: * the rough opening - the width of the hole in the wall into which the window will be fitted * the frame size - the width between outer parts of the window frame * the inside reveal to inside reveal width- the width between the timber trim around the window on the inside of the wall * the daylight opening - the unobscured glass width * the sash dimension - the dimension of the opening part of the frame All these measurements have different uses and by, for example specifying only the rough opening width, the exact type of window frame does not need to be specified.
What is the frame of a pistol?
The part that holds all the other parts.
How can I install window blinds by myself?
Window Blinds are quite simple to install. Typically blinds have two components that need to be installed on the top sides of the window frame. Then in the middle of the top part of the frame, is an additional component to be attached, that will offer support in holding the blinds up. All of the components will screw in directly to the window frame, and just need to be placed on a level line. The Blinds will have a top piece that will fit into the installed components, and mechanisms to secure it all.
What household things are made of trees?
All things wooden and paper... such as wooden furniture, window sills, doors, wooden flooring, bread-bin, cutting board, drawers, books, plus lots of other things.
Is it bad luck if you break a picture frame?
No it isn't - it removes all the bad luck caught up in the frame and gets it out the window, so now you have been freed from all your worries!
How can you get difficult to roll up windows to roll up easier?
Remove the inner door panel and lubricate all moving parts - with grease or graphite lubricant, if this does not help, the window frame in the door may be bent slightly.
How do you replace the rear slider window in a ford van?
I have replaced my drivers rear slider window on two occations. you need to first find a window from a wrecking yard and then there are screws and bolts around the frame. Take these out and then gently pry around the frame where you will find some black soft tar-like stuff that weatherproofs the window. Keep prying gently. Be careful or you will break the new window. eventually the window will come away from the frame. You will need to purchase the black weatherstriping gook that comes as a roll. Clean the new window if it is used of all the old sealant with a razor blade or chisel gently. and put a caulking bead around the frame before installing it in the new frame. That is the best I can tell you.
When will a window frame will expand to fill the entire desktop frame?
You should all know this its easy!! D. clink the title bar button marked with a single square.
How do you replace a rear door lock actuator in a 2003 land rover discovery ii?
With the front you need to remove the window frame to access the actuator. 5 bolts for the front window. 4 on all 4 corners of the frame and one directly in the middle. You might have to rip some of the plastic, use a box knife so you can tape it back up. After you remove the frame the actuator will be 100% easier to replace, you can actually see what you're doing. Also, the bolts are different sizes, do NOT THINK they can be interchanged. Long bolts go back where they came from, same with the short bolts. Good luck!ADD: Forgot to mention. Pull the frame slowly off the window, then lower the window a bit with your hand supporting it. There will be two screws holding the window to the regulator, unscrew them and lift the window out. Find a nice patch of grass to lay the window. When you put it back together remember, window in fist, bolt it in! Then, slide the frame over the window and tighten it down.Remember, roll your window all the way down with the door open. The black frame around the window. Yes you must remove the torx bolts to get the frame AND the actuator out, you can run to Lowe's and pick up the torx bits for cheap. Once the interior panel is removed there is no other metal frame just plastic wrap. It's hard to imagine but once you get frame and window out it will create A LOT more room to access the actuator. Oh, be VERY careful not to bend your window regulator rolling it up and down when the window is out, learn from my mistakes! One more thing, don't unplug your battery, you'll need to roll you window up and down to access the window regulator bolts.
Where do I get a liftgate window support arm?
They are made to be purchaswed at all auto parts stores.
