0
to detect maximum peak os AC signal and convert to DC signal
Wiki User
∙ 10y ago
Wiki User
∙ 11y agoAmplitude measurementAutomatic gain control
Data regeneration
Add your answer:
Earn +20 pts
Application of room noise detector?
A room noise detector could serve as a burglar alarm during the night and when away from home, of course, if no noisy dogs or other pets. It could serve as a child protection device, near a door to the outside of the home or near a swimming pool gate to alert the adults of he child's presence near the pool, or a road with traffic.
What is peak to peak?
Peak to Peak is the most positive peak to the negative peak value. Or find any peak value and multiply by 2.
Can you apply 230 v ac to kbpc2510?
we can apply 230v ac to kbpc2510 maximum peak voltage is 325v (for 230v) and its blocking capacity is about 1000v so we can use it (I used for the same application)
What is the effective value of 200 volts peak-to-peak?
200 volts peak-to-peak is 100 volts peak, which is 70.7 volts rms (standing for root-mean-square) also called "effective". This 70.7 volts is the DC voltage with the same heating power as the peak-to-peak. The relationship is: rms (aka RMS) equals peak-to-peak divided by 2, then divided again by square-root of 2 (1.414). The division by 2 gets us from peak-to-peak to just peak. The next division takes us to rms. If you get an AC voltrage with no description, for exmple 120 volts AC, it is RMS (effective). The USA AC standard supply voltage is 120 (also called 117) volts RMS. The USA peak is 117 x 1.414 (square root of 2) = 165 volts peak, = 330 volts peak-to-peak.
Are peak-to-peak and rms voltage measurements the same?
No, the peak-to-peak voltage is 2sqrt(2) times as much as the rms for a pure sine-wave.
What is the application of room noise detector what is the objective of room noise detector What are the modified application of the room noise detector?
tagos
What is peak detector?
a device which output voltage is almost the real peak valueof an applied signal
What are applications of peak detector?
Amplitude measurementAutomatic gain control Data regeneration
What difference between pda and uv detector in hplc?
PDA - Photo diode array UV- Ultra violet with use of PDA detector, we can measure the area or height of particular peak at different wavelengths ranging from 200 to 800 nm by injecting the solution at once. Where as in uv detector we can measure the area or height of the peak only at two different wavelengths. But that wavelengths also to be selected before injecting the solution.
What is quasi peak?
Most radiated and conducted limits in electromagnetic compatibility (EMC) testing are based on quasi-peak detection mode. Quasi-peak detectors weigh signals according to their repetition rate, which is a way of measuring their "annoyance factor." They do this by having a charge rate much faster than the discharge rate. Therefore as the repetition rate increases, the quasi-peak detector does not have enough time to discharge as much, resulting in a higher voltage output (response on spectrum analyzer). For continuous wave (CW) signals, the peak and the quasi-peak response are the same. The quasi-peak detector also responds to different amplitude signals in a linear fashion. High amplitude low repetition rate signals could produce the same output as low amplitude high repetition rate signal. Quasi-peak detector readings will always be less than or equal to the peak detection. Because quasi-peak readings are much slower, (by 2 or 3 orders of magnitude compared with peak) it is very common to scan initially with the peak detection first, and then if this is marginal or fails, switch and run the quasi- peak measurement against the limits.
What is the peak of Fentanyl patch?
The peak of pain relief provided by the Fentanyl transdermal system is between 12 and 18 hours after application.
What is the deadline to fill out the peak performance application for UCCS?
Nov 15 2012
When was the inventor of the metal detector born?
the metal detector was invented because people in old days use to use it so they could find stuff in there body I think
State 5 type of temperature measuring devices other than thermocouple with its application?
RTD - Resistence temperature detector Thermistor Pyrometer Thermometer
What has the author K Svanholm written?
K. Svanholm has written: 'Gamma thermometer and neutron detector application' -- subject(s): Neutron counters, Themometers and themometry
What is the difference between detector and diode detector?
difference between detector and diode
What is alpha particle detector and what is the application of bjt in alpha particle detector?
A Geiger counter, also called a Geiger-Müller counter, is a type of particle detector that measures ionizing radiation. They detect the emission of nuclear radiation: alpha particles, beta particles or gamma rays. A Geiger counter detects radiation by ionization produced in a low-pressure gas in a Geiger-Müller tube
