0
What are the effect of over tightening the compression fitting?
Wiki User
∙ 10y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Advantage of bzip2 compression algorithm over other algorithms?
Archives are smaller than with gzip. Compression requires more resources though.
What is a method of removing repetitive elements from a file so that the file requires less storage space and therefore less time to transmit over a network?
Compression.
How do you install a well-saver LPT20 tank?
I did it the easy way. I bought a BRASS compression coupling (Plumbing supply House) , Plastic won't take the tightening required for a pressure seal. I just hack sawed off the "tee" part and connected the 2 straight sections with the Brass coupler. I have replaced my Well Saver LPT20 twice over the years with this technique. They tend to rust out underneath at the weld after several years.
What are ferrules used for in plumbing?
A ferrule is used on a compression type joint. Care should be taken to properly tighten the nut, but typically it goes between the nut and a fitting. You should use plastic ferrules on plastic pipe but also be sure to use a brass or stainless sleeve inside the open end of the pipe so you don't crush it and it maintains therigidity of the pipe. You should use a brass ferrule on copper pipe which are stronger and give a better squeeze on the pipe sealing the joint. Usually hand tight plus a 1/2 turn is good to start with. water test the fitting and if it leaks you can always shut it back off and tighten more. One rule of plumbing is tight is tight, too tight is broke! There is no need to apply pipe sealant, pipe dope, or Teflon tape to the threads of the compression nut. None of these things will hurt, but they won't help either, since the seal depends ONLY on how well the ferrule is compressed against the pipe and the taper of the fitting. If the fitting leaks, it is because something is wrong. You could have over- or under-tightened the nut, the ferrule might have been damaged, the taper might have a nick in it, etc.
What is the effect of over loading in dc machine?
Heat, smoke, fire...
How ferrule works?
In small sizes, the compression fitting is composed of an outercompression nutand an innercompression ringorferrulethat is typically made of brass or copper. Ferrules vary in shape and material but are most commonly in the shape of a ring with beveled edges. To work properly, the ferrule must be oriented correctly -- usually the ferrule is fitted such that the longest sloping face of the ferrule faces away from the nut.When the nut is tightened, the ferrule is compressed between the nut and the receiving fitting; the ends of the ferrule are clamped around the pipe, and the middle of the ferrule bows away from the pipe, making the ferrule effectively thicker. The result is that the ferrule seals the space between the pipe, nut, and receiving fitting, thereby forming a tight joint.Larger sizes of compression fitting do not have a single nut to compress the ferrule/olive but a flange with a ring of bolts that performs this task. The bolts have to be tightened down evenly.Thread sealants such as joint compound (pipe dopeorthread seal tapesuch as PTFE tape) are unnecessary on compression fitting threads, as it is not the thread that seals the joint but rather the compression of the ferrule between the nut and pipe. However, a small amount ofplumber's greaseor light oil applied to the threads will provide lubrication to help ensure a smooth, consistent tightening of the compression nut.It is critical to avoid over-tightening the nut or else the integrity of the compression fitting will be compromised by the excessive force. If the nut is overtightened the ferrule will deform improperly causing the joint to fail. Indeed, overtightening is the most common cause of leaks in compression fittings. A good rule of thumb is to tighten the nut first by hand until it is too difficult to continue and then tighten the nut one half-turn more with the aid of a wrench; the actual amount varies with the size of the fitting, as a larger one requires less tightening. The fitting is then tested: if slight weeping is observed, the fitting is gradually tightened until the weeping stops.The integrity of the compression fitting is determined by the ferrule, which is easily prone to damage. Thus care should be taken to when handling and tightening the fitting, although if the ferrule is damaged it is easily replaced.In a bind, master plumbers have been known to replicate the sealing action of a ferrule by using an artfully "woven" piece of thread seal tape. This is attempted as a temporary solution to prevent a leak until a proper ferrule can be procure
What is a FTG x C copper fitting?
C = cupped end - the type you would slide over another pipe to make a sweat connection FTG = fitting end - the type that slides inside a cupped end, also called a "street" fitting M = male pipe threads FE (sometimes listed as just F, not correct)= female pipe threads The "X" is "by", so C X C is "cupped by cupped", a fitting with two ends such as a coupling or elbow, both cupped for sweating onto a pipe or fitting end. C X C X C would be a fitting with three ends such as a tee, all cupped. C X FTG could be a street elbow or a reducing bushing, one part slides over a pipe, the other inside another cupped fitting. C is indeed a cupped fitting. CMP is compression, but there is no such thing as a copper fitting with a compression connection. There are brass and plastic compression fittings that will fit copper pipe, but not copper compression fittings.
How can you fix a hose that connects the filter to the return and is leaking at the connection?
Could be as easy as tightening the hose clamp. However if the hose being cut by over-tightening the clamp caused the leak, you may be able to loosen the clamp, slide the clamp to a good section of hose, and retighten. Be sure that the fitting is not collapsing. If it is, replace it, remembering to use Teflon sealing tape on the fitting threads. If the hose is too badly damaged it may need replacement.
Why will water not stay in your washer and leaks all over floor?
Pump or fitting is leaking underneath the washer, the hose where it attaches to the washer needs tightening or the hose itself is not high enough to prevent the water from just running out.
How do you change fuel pump on Ford Laser 1.3?
Two bolts and hoses. When fitting to KA /KB, the arm on the pump goes UNDER the cam. Later B6 engines the arm goes OVER the cam. If you put the early model over the cam you will break the arm when tightening the bolts, Chris
How do you change a fuel filter on a 95 Dodge Intrepid 3.5 liter 24 valve?
You need a special tool that slides into the end of the fitting of the fuel filter. Its commonly called a fuel filter remover. it should be a round peice of plastic or mettal that clips over the fuel line and slides into the end and releases the compression fitting
What are compression fittings used for?
Compression fittings are used to join two tubes or pipes together. Typically it is used when the two pipes are different materials or different sizes. They are also sometimes used on pipes where it is difficult to solder or maybe dangerous to do so.
What causes oil pan hole to be stripped?
Over tightening the drain plug.
What is a close fitting female garment worn over a blouse?
Answer : Shruga short jacket or close fitting cardigan
How do you determine the compression stroke on a 350 Chevy engine?
Remove all the spark plugs and turn the engine over by hand. Place your thumb over the #1 plug hole and you will feel the pressure on the compression stroke. A compression gage will also tell you when you are on the compression stroke.
Can you over tighten compression fittings?
yes
What is an example of compression science?
A example of a compression is a weight over a mans head. The man would of found out that his body was being compressed by the weight over his head.
