0
What are the steps to program the keyless remote on a 1999 Kia Sportage?
Wiki User
∙ 18y ago
Kia Sportage Factory Keyless Remote Entry Transmitter Programming Instructions. 1. Open driver's door and turn ignition to "ON" position 2. Locate the programming button on wiring harness pigtail, behind the left side of the center console (to the right of the gas pedal), next to the RKE module. (feel around under the plastic wall) 3. Press & Hold the button for 15 seconds. The horn will sound 3 times when it enters programming mode. 4. Press the lock button on the transmitter. The horn should sound once to confirm the transmitter. Repeat for any additional transmitters up to 4 max 5. Turn ignition to "OFF" and test transmitters. This worked on my 2001 Sportage perfect! I had to pay some guy for these instructions so here you are guys! Good Luck!
Wiki User
∙ 18y ago
Add your answer:
Earn +20 pts
How to program keyless remote 94 firebird?
The guy at Pontiac said it requires a series of steps. He wasn't even sure. The Pontiac dealership will program it though for $60 so this question is really worth answering. Sorry I couldn't help.
How do you program a 2004concorde a spare keyless entry?
To program the 2004 Concorde spare keyless entry, you can take the vehicle to the dealer or you can download the manual. In the manual, there are steps to reset the keyless entry using your vehicle's VIN and other identifications.
Keyless entry for a 2005 Chevy trailblazer - you cannot program a new remote - you go thru the steps to reset and after following the instructions you cannot set a remote what other issue could you be?
One of our forum members can probably help you out at www.trailvoy.com Enthusiasts helping other Trailblazer owners!
How do you program remote control for Ford Escape xlt 4x4 2002?
From thrashin: Ford Escape Remote Transmitter Programming NOTE: Make sure remote batteries are OKNOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered.NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), carry out the following steps. Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met. Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.
How do you prograre your Dish Network remote to your Curtis Mathes tv?
To program your DISH Network remote to your TV there are a few different DISH Network remote codes that you can try & will need in order to successfully program your remote to the TV. The DISH Network remote codes for your Curtis Mathes TV will be one of the following, 516, 531, 595, or 253. If you are unsure how to perform the steps to program
How do you Program kobut1bt?
KOBUT1BT is the FCC ID# on the back of keyless entry remotes for 2000-2001 Chevy Full Size Pickup/1998-2004 Chevy S-10 Pickup/2000-2001 Chevy Suburban & Tahoe. And it's easy to program these remotes without having to pay dealership "ripoff" prices. 01: Close all vehicle doors02: Insert key into ignition03: Press and hold driver's door unlock switch04: Cycle igniton On_Off_On_Off05: Release unlock switch Doors will lock and unlock to confirm programming mode 06: Press and hold lock & unlock buttons on keyless remote Doors will lock and unlock to confrim keyless remote programmed 07: Release lock & unlock buttons on keyless remote Repeat steps 06 & 07 on all remotes you have for vehicle because programming first remote erases programming on additional remotes. 08: Turn igniton on to exit programming mode Up to four remotes can be programmed to one vehicle.
How do I program a Toshiba remote?
The steps to program that remote are listed below! Addressing Remote to TV: 1.) Press and hold the clear TV button until all mode lights light up. 2.) Release and TV light will be blinking. 3.) Enter code and press #. The TV button should flash 3 times. 4.) Try functions (Volume, Power, etc..) and see if it is working. 5.) If no function, repeat steps 1-4 with another code.
How do you program a 2003 Honda Accord keyless remote?
You must complete each step within 5 seconds of the previous step to keep the system from exitingthe programming mode.1. Turn ignition switch to ON (II)2. Press the LOCK or UNOCK button on one of the remotes. (An unprogrammed remote can be used for thisstep.)3. Turn ignition switch to LOCK (0)4. Repeat steps 1, 2 and 3 two more times using the same keyless remote used in step 25. Turn the ignition switch to ON (II)6. Press the LOCK or UNLOCK button the same remote. Make sure the power door locks cycle to confirm youare in programming mode.7. Press the LOCK or UNLOCK button on each remote you want to program. Make sure door locks cycleafter you push each remote button to confirm system has accepted the remote.8. Turn the igniton switch to LOCK (0) to exit programming mode.9. Test remote(s)
Can a RCA universal remote control work with a precision tv?
i tried using the precision code 166 to program the tv bgut it didnt work. i used an RCA remote control and followed all the steps.
What is the Dish network remote control code for a durabrand tv?
The steps on how to program a remote are below! These steps will work with all DISH remotes. Addressing Remote to TV: 1.) Press and hold the clear TV button until all mode lights light up. 2.) Release and TV light will be blinking. 3.) Enter code and press #. The TV button should flash 3 times. 4.) Try functions (Volume, Power, etc..) and see if it is working. 5.) If no function, repeat steps 1-4 with another code.
How To Add Second Remote to 2007 Toyota Highlander?
u do it the same way as the first one. ie follow the same steps, but hold the 2nd button to program it to that button
How do you program you 5.4 Ir dish remote for TV?
Below are the steps to program a remote to your second TV. Addressing Remote to Receiver: 1.) Take your TV2 remote to your TV1. 2.) Go to System Info screen from the TV1. 3.) Hold down the SAT button on your TV2 remote until all mode lights light up. 3.) Enter a number between 1 and 15 using the numeric keypad on the remote. 4.) Press the pound (#) button. 5.) Once the SAT button blinks three times, press record. 6.) Test remote and see if it works.
