Air Filters and Intake Manifolds
Ford Escape XLT
Chevy 350
1995-2005 Chevy Cavaliers

What are the torque specs on intake manifold bolts and exhaust manifold bolts for a 97 Chevrolet Cavalier 2 2 liter engine?

979899

Top Answer
User Avatar
Wiki User
2010-05-29 21:24:11
2010-05-29 21:24:11

24 ft lbs lower intake

115 inch lbs exhaust

12
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

If your 1988 Chevrolet Celebrity has the V6 engine the oxygen sensor is in the middle of the exhaust manifold nearest the firewall. If you have the 4 cylinder engine the oxygen sensor is located in the exhaust manifold just above the exhaust pipe flange.

User Avatar

In the exhaust manifold behind the engine.In the exhaust manifold behind the engine.

User Avatar

If it's an automatic you will have to remove the exhaust manifold because the thermostat is located on the backside of the engine on the driver's side under the exhaust manifold.

User Avatar

In the exhaust manifold on the back of the engine.In the exhaust manifold on the back of the engine.

User Avatar

There are 2...On the exhaust manifold and after the cat. converter

User Avatar

It only has one. It is located in the exaust manifold in front of the engine. Four cylinder that is. If by chance you have a V6, then it would have two, both located in the exhaust maifolds, on the front, and back of the engine.

User Avatar

2.2L Between the radiator and engine,,,, 2.4L Between the engine and firewall....both bolted to the engine head.

User Avatar

The intake manifold is where the air and fuel mix and enter the engine. The exhaust manifold is where unspent gas and air exit the engine. In other words the intake manifold is where the engine breathes in and the exhaust manifold is how the engine exhales out.

User Avatar

exhaust manifold is where exhaust pipe hooks to engine!

User Avatar

Front of the engine, just below the exhaust manifold.Front of the engine, just below the exhaust manifold.

User Avatar

Front of the engine, just below the exhaust manifold.Front of the engine, just below the exhaust manifold.

User Avatar

On the 2.2L engine they are in the front between the exhaust manifold. On the 2.4L engine they are under the aluminum cover on the top of the engine. There are no plug wires on the 2.4L engine.

User Avatar

the engine block will be the same. you may have to keep the s-10 intake manifold and exhaust manifold to match up with the wire harnes and exhaust. should be easy

User Avatar

Routes exhaust gases out of engine bay

User Avatar

The exhaust manifold is the header that starts at the piping on the driver's side of the engine and runs back out to the exhaust.

User Avatar

exhaust pipe connects to the exhaust manifold, which connects to the main engine.

User Avatar

located on the water pump housing on back passenger side of the engine under the exhaust manifold.

User Avatar

Back of the engine, center, under the exhaust manifold. According to autozone.com

User Avatar

you can bolt up engine but you will more than likely have to exchange exhaust manifold as well as the computer  ecm/pcm/ecu its diffently not p[lug and play  

User Avatar

The exhaust manifold needs to have a gasket in place to help seal the juncture between the manifold and the engine. After the gasket and gasket sealer are in place, tighten the bolts for the exhaust manifold. The exhaust pipe can then be replaced on the new exhaust manifold.

User Avatar

Yes, but the exhaust manifold (due to the flange where it connects to the exhaust pipe is different) and the intake manifold (due to the EGR Valve) will have stay with the car. And it would be a great time to change the water pump, because of the huge pain in the back it is with the engine in the car.

User Avatar

The oxygen sensor is in the rear exhaust manifold. You should be able to see it by looking behind the engine from inside the engine bay.

User Avatar

At the engine end of the upper rad hose. If you're looking straight onto the engine. Look for the exhaust manifold. Just left of the exhaust manifold you will see a coolant hose connect to what look like a adaptor. The thermostat is located under that housing.

User Avatar

Exhaust manifold on the front of the engine, exhaust manifold on the rear of the engine and another down stream by the catalyst.

User Avatar

The crankshaft position sensor is located on the lower engine block beneath the exhaust manifold on the firewall side of the engine.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.