What cables carry the signal from a cable modem to a PC is it a RCA cable HDMI ethernet or coaxial?
RG-58 coaxial cable is used for thin Ethernet.
Fiber-Optic (CAT5 or ethernet) cables are slightly thicker than a phone line. Coaxial cables are a single pin screw in connection. fiber optics can handle far more data, and a lot faster that a coaxial connection.
E1 is coaxial cable @2Mbps, compared to ethernet@10/100Mbps, Coaxial cable very expensive compared to ethernet.
Coaxial and ethernet. The round one is coaxial, the rectangular ones are ethernet.
How does the twisted pair and coaxial cable the signal differ from the signal in the fiber optic cable?
fiber -optic cable signal is light signal coaxial and twisted pair signal electrical
Look for cables with the most shielding. The shielding in coaxial cable can be from a little to almost 100 percent. The better cables will have the most shielding.
Coaxial cable (multiple cables with a common axis) is widely used for signalling as the outer cable acts as a screen for the inner cables. Coax is ideal for short/medium distance signals - it's easy to interface to, and cheap. For longer distance, it has some disadvantages - the signal starts to decay over distance and repeaters have to be used to reamplify the signal.
Instrumentation cable carries a digital protocol such as devicenet, profibus, foundation fieldbus or even ethernet. Compared to regular hard wired devices that would use coaxial cables.
Coaxial cables are conductors that send an electrical signal through an inner conductor which is surrounded by a protective insulating layer and sealed by a shield. The cable itself is protected by the outside insulating layer. Coaxial cable is commonly used for video and CATV transmission. The advantage is that electromagnetic fields have less leakage outside the shield.
Coaxial cable has a thicker shielding than most other cables.
Media means type of data transfer, cable and connector but cable and connector can also be called medium. and coaxial is a type of cable which is mainly used for ethernet
Twisted pair wiring is a digital signal. Coaxial cable is an analog signal.
There are two types of cable used for television radio frequency signals: 300 ohm twin lead flat cable and 75 ohm coaxial cable. The twin lead is typically used with a rabbit ears antenna and coaxial is typically used with roof top antenna or cable TV setups. For television baseband video signals coaxial cables are usually used. However for digital television baseband video signals these are not adequate and special cables (e.g. HDMI, DVI, DisplayPort)… Read More
You need a special adapter that usually run $17.
Coaxial cable, Optical fiber cable, Twisted Pair
A coaxial cable has great uses in television antenna connections. TV satellite connections also use coaxial cables to connect decoders to the TV set.
Thinnet coaxial cable uses a BNC twist connector.
No, the standard Ethernet cables can have up to 100 meters. No, the standard Ethernet cables can have up to 100 meters. No, the standard Ethernet cables can have up to 100 meters. No, the standard Ethernet cables can have up to 100 meters.
Electrical signal - is used by twisted pair cable and coxial. Light signal - is used by fiber optic.
Can you run Ethernet cable and coaxial cable in the same hole and outlet cause in a book it said not to use the same hole?
You should not run communications cables with power cables. That causes interference on the data cables. Coax/video and Ethernet should not interfere with each other at all, and you can commonly buy wall face plates that have connectors for both data and video. You do want to make sure that there is enough room in the holes for both cables to move freely without snagging or binding.
A Cat 5 cable is an Ethernet cable, used in computer networks. Cat 5 cables are designed for high signal integrity, and can carry two separate telephone lines.
The purpose of a coaxial cable is to act as a transmission line for a radio frequency signal. The electromagnetic field carrying that signal exists only in space between its inner and outer conductors.
The bit error rate is a standard transmission-error rate of a medium such as copper wire, coaxial cable, or fiber-optic cable. Coaxial cables have a low error rate that is generally 1 in 1 billion bps.
First you must have an internet service provider and it then depends on what equipment they have provided. An ethernet cable will connect to a modem or a router and go to the device for a wired connection. I used a Cat 6 ethernet cable and a router to split the signal from my first cable modem to a router and then from my PS3 and PC connected 2 more ethernet cables to the back… Read More
If you count a router cable as a ethernet cable, yes. An ethernet cable is what you plug from your xbox into a laptop/router/modem to connect to xbox live. The following SKU's come with ethernet cables. *Xbox 360 PRO *Xbox 360S *Xbox 360 Elite The xbox 360 CORE and ARCADE have no ethernet cables. Hope this helped.
Cable internet works by transmitting signals and information via the same coaxial cables that cable television uses. The transmission is sent through a designated television channel that is managed by the cable provider. The signal is received by a cable modem box, which is installed into the user's home.
Can a coaxial cable for a TV go bad Can you suddenly lose the signal from an antenna because of a bad cable or connection from the TV to the wall jack Will a new cable solve this problem?
Yes! a coaxial cable can go bad. Yes! you can suddenly lose the signal from an atenna because of a bad cable. A a new coaxial cable may fix the problem as long as the damaged cable is the source of the problem. However if the signal problem is at the tap or one of the splitters in your home you will need to call your cable company to fix the problem.
You do not need specific cables for the PS2's Ethernet jack. Ethernet is standardized; any CAT5 cable will work fine for use on a PlayStation 2.
No. Telephone cables have a different kind of connector. Networking cables (also known as Ethernet cables) are also a bit wider then telephone cables.
The difference between baseband coaxial and broadband coaxial cable is baseband coaxial technology uses digital signaling in which the cable carries only one type of digital signal. Where as the broadband coaxial technology typically transmits analog signals and is capable of transmitting multiple frequencies of data simultaneously.
The UTP cable it uses an RJ-45 connector. For coaxial cable, it will be either an F connector or a BNC connector.
Different types of network cables, such as coaxial cable, optical fiber cable, and twisted pair cables, are used depending on the network's physical layer, topology, and size. The devices can be separated by a few meters (e.g. via Ethernet) or nearly unlimited distances (e.g. via the interconnections of the Internet). Cables are used in different fields like technology, hospitals & everywhere. You will get quality medical cables from Peterstechnology.com at an affordable price.
Yes you can get a crossover cable for any of the Ethernet cable series on one end of the cable two of the smaller cables inside are crossed over so they are not straight through cables
Several types of cables are used, depending on the specific type of Ethernet. The cables most commonly used nowadays, however, are UTP (unshielded twisted pair) - and for longer distances, fiber optic.
Generally speaking, RG6U can replace 5C-2V coaxial cable because these are cables with very similar characteristics. RG6U cable is even better because it has lesser attenuation than 5C-2V. So you can without a doubt use this cable if you're replacing cable for your TV.
Coaxial Cables 10Base5(thicknet) and 10Base2(thinnet) are used
optical fiber ,twited pai,coaxial cable
fiber optic, coaxial, and twisted-pair
Fiber optic cables are nothing but another transmission medium. All the protocol which works on Ethernet cable will work in Fiber optic cable also. In case of Ethernet, the digital data will be sent in electrical signal format. But Fiber Optic cables are passive devices. They can not conduct electrical signals. So the digital data signals needs to be converted to Optical signal before sending that via fiber. Usually after the conversion process, the header… Read More