0
What can you do if your lights won't turn on and you've already replaced the light switch?
Wiki User
∙ 18y ago
Did you check the fuse?
Wiki User
∙ 18y ago
Add your answer:
Earn +20 pts
Why are lights dim after the switch was replaced?
Because the juju has yet to be established in the new wiring. As soon as the juju takes hold, the light brightens. <<>> Recheck your wiring of the switch. It sounds like you may have wired two lights in series that may have been supplied from the one switch. Two lights from one switch have to be wired in parallel with each other. Use the discussion page if you need help with this problem
If you travel at the speed of light in a car and turn your headlights 'ON' What will Happen?
To travel at the speed of light you would have to BE light so i guess you would became an even brighter light The switch to turn on the lights will work but no light will come on as you are already at that speed
What is the bulb in the light switch for on a Mercedes?
when you have your lights on, if you pull the switsh outwards, this will turn your fog lights on, the bulb is just to tell you your fog light are on.
You have three 3-way switches operating 3 ceiling lights you want each switch to operate each single light What do you do?
wire each switch to each light...
How do you hook up an overhead light in the kitchen to a two way switch?
use a parallel circuit to make many lights light up at the same time as the switch is turned on.
What would cause the parking lights tail lights license plate lights and dash lights not to work on 1994 Chevy Z71 already have checked the fuses and replaced all bulbs?
The light switch.
What can it be if the reverse lights on a 2005 chevy cavalier 5 spd dont work bulbs already been replaced and fuses are good?
Defective reverse light switch.
Why do your headlights parking lights and dash lights not work you have replaced dimmer switch light switch and fuses and still no luck?
could be bad wiring
1985 bronco brake lights dont work but all other lights do work you replaced brake light switch and bulbs?
Check the brake light fuse. If you have 12 volts at the brake light switch I would suspect the signal light switch is at fault.
2000 camaro dash lights not working. I replaced the headlight switch and still nothing. But if I jump the switch dash lights come on. So light bulbs do work.?
check the fuse for dash lights
Why would the brake lights on your 95 ls turn on while the car is off and kill your battery?
Sounds like Stop light switch needs to be replaced Sounds like Stop light switch needs to be replaced
My tail lights and third brake light work on my 98 Explorer the two main brake lights do not Already replaced the brake light switch and all fuses appear to be intact What next?
I hate to ask , but did you check the bulbs ? The tail light portion may work fine , but the brake lights don't if both of the bulbs are bad .
What is wrong if the stoplights don't work but the tail lights and rear signal lights work and the stop light light bulbs have been replaced and the fuses checked?
brake light switch bad check for continuity at the fuse then the switch, but yeah bad switch. Kongkit Raggan-Supatanampon
How do you turn off the SRS light on a 2001 Honda Accord EX?
i have a 1995 Honda accord 4 cylinder v tec the tail lights sides lights and the dash lights stays on at all times have already replaced the headlight switch and still have the same proplome
Brake lights do not work all the time replaced brake light switch?
If you have the same bulb for brake and signal, brake light power needs to be interrupted by the signal lights, The brake circuit has to go through the signal light switch so the problem could be there.
Why don't Brake lights work on 96 Camry cruise works lights work and replaced brake light switch?
Check the fuse. Then check the wiring.
Why would the brake lights stay on whenever the car is on even after you have replaced the brake light switch?
Out of adjustment. Adjust the mounting of the switch so the brakes lights are off until you press the brake pedal.
