Too much amperage in the circuit. Find what is causing the increase in voltage.
Use a fuse
if it matches the current rating.... then no problem.
Fuses That "Blow"Without being able to "hands on" troubleshoot the circuit served by the repeatedly blowing fuse, no one can identify the specific cause/defect which is causing your problem.The following generic answer applies to any electrical circuit, whether in a vehicle, or in a building, or whether alternating current [AC] or direct current [DC].Fuses [and Circuit Breakers] are safety devices designed and installed in electrical circuits TO PROTECT the conductors [wires] and other components from short circuit conditions and/or overload conditions which cause an extremely large flow of electrical current [measured in Amperes], which causes overheating of the conductors that results in damage to the insulation and the conductors.And in a worst case scenario, the probability of a FIRE which could destroy the vehicle, house, or other structure in which the circuit is located.When a fuse or Circuit Breaker [and replacement fuses, or "tripping" Circuit Breakers] "blow," especially if it happens repeatedly, is an indication of an UNSAFE CONDITION in that circuit, usually a short.The fuse or circuit breaker is doing what it was designed, intended, and installed to do, protect the conductors and components of the circuit which it serves.The proper "fix" is for a qualified technician, who knows what he or she is doing, to troubleshoot the involved circuit, find and identify the defect, and make proper repair [s], BEFORE replacing the fuse again [with the properly sized fuse or before resetting a circuit breaker].Some ignorant few will suggest installing a larger fuse or breaker to solve the problem, BUT that will only increase the hazard, not correct it. Do not follow "bad" advice by installing a larger fuse in a misguided attempt to correct the problem. To install an over-sized fuse would almost guarantee damage to the wiring and an electrical system fire.
"Blowing" FusesFuses blow because there is a defect in the circuit in which it's installed to protect. To help in understanding see the following answer to a similar question regarding fuses that repeatedly continue to blow after replacement.Fuses That "Blow" RepeatedlyWithout being able to "hands on" troubleshoot the circuit served by the repeatedly blowing fuse, no one can identify the specific cause/defect which is causing your problem.The following generic answer applies to any electrical circuit, whether in a vehicle, or in a building, or whether alternating current [AC] or direct current [DC].Fuses [and Circuit Breakers] are safety devices designed and installed in electrical circuits TO PROTECT the conductors [wires] and other components from short circuit conditions and/or overload conditions which cause an extremely large flow of electrical current [measured in Amperes], which causes overheating of the conductors that results in damage to the insulation and the conductors. And in a worst case, the probability of a FIRE which could destroy the vehicle, house, or other structure in which the circuit is located.When a fuse or Circuit Breaker [and replacement fuses, or "tripping" Circuit Breakers] "blow," especially if it happens repeatedly, is an indication of an UNSAFE CONDITION in that circuit, usually a short.The fuse or circuit breaker is doing what it was designed, intended, and installed to do, protect the conductors and components of the circuit which it serves.The proper "fix" is for a qualified technician, who knows what he or she is doing, to troubleshoot the involved circuit, find and identify the defect, and make proper repair [s], BEFORE replacing the fuse again [with the properly sized fuse or before resetting a circuit breaker].Some ignorant few will suggest installing a larger fuse or breaker to solve the problem, BUT that will only increase the hazard, not correct it. Do not follow "bad" advice by installing a larger fuse in a misguided attempt to correct the problem. To install an oversized fuse would almost guarantee damage to the wiring and an electrical system fire.
Yes, as long as the fuse is able to be inserted into the fuse holder it will work.
Blowing Fog Light FuseI have used the following answer for questions regarding fuses that blow repeatedly, BUT... it also applies to fuses that blow only once alsol Fuses That "Blow" RepeatedlyWithout being able to "hands on" troubleshoot the circuit served by the repeatedly blowing fuse, none of us can identify the specific defect which is causing your problem.Therefore, the following generic answer can be applied to any electrical circuit, whether in a vehicle, or in a building, whether direct current [DC], or alternating current [AC].Fuses [and Circuit Breakers] are safety devices designed and installed in electrical circuits TO PROTECT the conductors [wires] and other components from short circuit conditions and/or overload conditions which cause an extremely large flow of electrical current [measured in Amperes], which causes overheating of the conductors that results in damage to the insulation and the conductors.And in a worst case scenario, the probability of a FIRE which could destroy the vehicle, house, or other structure in which the circuit is located.When a fuse or Circuit Breaker [and replacement fuses, or repeatedly "tripping" Circuit Breakers] "blow," especially if it happens repeatedly, is an indication of an UNSAFE CONDITION in that circuit, usually a short.The fuse or circuit breaker is doing what it was designed, intended, and installed to do; that is to protect the conductors and components of the circuit which it serves.The proper "fix" for this issue is for a qualified technician, who knows what he or she is doing, to troubleshoot the involved circuit, find and identify the defect, and make proper repair [s], BEFORE replacing the fuse again [with the properly sized fuse or before resetting a circuit breaker].Some ignorant few people will suggest installing a larger fuse or breaker to solve the problem, BUT that will only increase the hazard, not correct it.Do not follow "bad" advice by installing a larger fuse in a misguided attempt to correct the problem. To install an oversized fuse would almost guarantee damage to the wiring and the probability of an electrical system fire.
Fuses That "Blow" RepeatedlyWithout being able to "hands on" troubleshoot the circuit served by the repeatedly blowing fuse, no one can identify the specific cause/defect which is causing your problem.Therefore, the following generic answer can be applied to any electrical circuit, whether in a vehicle, or in a building, or whether alternating current [AC] or direct current [DC].Fuses [and Circuit Breakers] are safety devices designed and installed in electrical circuits TO PROTECT the conductors [wires] and other components from short circuit conditions and/or overload conditions which cause an extremely large flow of electrical current [measured in Amperes], which causes overheating of the conductors that results in damage to the insulation and the conductors.And in a worst case scenario, the probability of a FIRE which could destroy the vehicle, house, or other structure in which the circuit is located.When a fuse or Circuit Breaker [and replacement fuses, or "tripping" Circuit Breakers] "blow," especially if it happens repeatedly, is an indication of an UNSAFE CONDITION in that circuit, usually a short.The fuse or circuit breaker is doing what it was designed, intended, and installed to do, protect the conductors and components of the circuit which it serves.The proper "fix" is for a qualified technician, who knows what he or she is doing, to troubleshoot the involved circuit, find and identify the defect, and make proper repair [s], BEFORE replacing the fuse again [with the properly sized fuse or before resetting a circuit breaker].Some ignorant few will suggest installing a larger fuse or breaker to solve the problem, BUT that will only increase the hazard, not correct it. Do not follow "bad" advice by installing a larger fuse in a misguided attempt to correct the problem. To install an over-sized fuse would almost guarantee damage to the wiring and an electrical system fire.
Fuses That "Blow" RepeatedlyWithout being able to "hands on" troubleshoot the circuit served by the repeatedly blowing fuse, none of us can identify the specific defect which is causing your problem.Therefore, the following generic answer can be applied to any electrical circuit, whether in a vehicle, or in a building, whether direct current [DC], or alternating current [AC].Fuses [and Circuit Breakers] are safety devices designed and installed in electrical circuits TO PROTECT the conductors [wires] and other components from short circuit conditions and/or overload conditions which cause an extremely large flow of electrical current [measured in Amperes], which causes overheating of the conductors that results in damage to the insulation and the conductors.And in a worst case scenario, the probability of a FIRE which could destroy the vehicle, house, or other structure in which the circuit is located.When a fuse or Circuit Breaker [and replacement fuses, or repeatedly "tripping" Circuit Breakers] "blow," especially if it happens repeatedly, is an indication of an UNSAFE CONDITION in that circuit, usually a short.The fuse or circuit breaker is doing what it was designed, intended, and installed to do, that is to protect the conductors and components of the circuit which it serves.The proper "fix" for this issue is for a qualified technician, who knows what he or she is doing, to troubleshoot the involved circuit, find and identify the defect, and make proper repair [s], BEFORE replacing the fuse again [with the properly sized fuse or before resetting a circuit breaker].Some ignorant few people will suggest installing a larger fuse or breaker to solve the problem, BUT that will only increase the hazard, not correct it.Do not follow "bad" advice by installing a larger fuse in a misguided attempt to correct the problem. To install an oversized fuse would almost guarantee damage to the wiring and the probability of an electrical system fire.
Fuses That "Blow" RepeatedlyWithout being able to "hands on" troubleshoot the circuit served by the repeatedly blowing fuse, no one can identify the specific cause/defect which is causing your problem.Therefore, the following generic answer can be applied to any electrical circuit, whether in a vehicle, or in a building, or whether alternating current [AC] or direct current [DC].Fuses [and Circuit Breakers] are safety devices designed and installed in electrical circuits TO PROTECT the conductors [wires] and other components from short circuit conditions and/or overload conditions which cause an extremely large flow of electrical current [measured in Amperes], which causes overheating of the conductors that results in damage to the insulation and the conductors. And in a worst case scenario, the probability of a FIRE which could destroy the vehicle, house, or other structure in which the circuit is located.When a fuse or Circuit Breaker [and replacement fuses, or "tripping" Circuit Breakers] "blow," especially if it happens repeatedly, is an indication of an UNSAFE CONDITION in that circuit, usually a short.The fuse or circuit breaker is doing what it was designed, intended, and installed to do, protect the conductors and components of the circuit which it serves.The proper "fix" is for a qualified technician, who knows what he or she is doing, to troubleshoot the involved circuit, find and identify the defect, and make proper repair [s], BEFORE replacing the fuse again [with the properly sized fuse or before resetting a circuit breaker].Some ignorant few people will suggest installing a larger fuse or breaker to solve the problem, BUT that will only increase the hazard, not correct it. Do not follow "bad" advice by installing a larger fuse in a misguided attempt to correct the problem. To install an over-sized fuse would almost guarantee damage to the wiring and an electrical system fire.
Fuses That "Blow"Without being able to "hands on" troubleshoot the circuit served by the blowing fuse, no one can identify the specific cause/defect which is causing your problem.The following generic answer applies to any electrical circuit, whether in a vehicle, or in a building, or whether alternating current [AC] or direct current [DC].Fuses [and Circuit Breakers] are safety devices designed and installed in electrical circuits TO PROTECT the conductors [wires] and other components from short circuit conditions and/or overload conditions which cause an extremely large flow of electrical current [measured in Amperes], which causes overheating of the conductors that results in damage to the insulation and the conductors. And in a worst case scenario, the probability of a FIRE which could destroy the vehicle, house, or other structure in which the circuit is located.When a fuse or Circuit Breaker [and replacement fuses, or "tripping" Circuit Breakers] "blows," especially if it happens repeatedly, is an indication of an UNSAFE CONDITION in that circuit, usually a short.The fuse or circuit breaker is doing what it was designed, intended, and installed to do, protect the conductors and components of the circuit which it serves.The proper "fix" is for a qualified technician, who knows what he or she is doing, to troubleshoot the involved circuit, find and identify the defect, and make proper repair [s], BEFORE replacing the fuse again [with the properly sized fuse or before resetting a circuit breaker].Some ignorant few will suggest installing a larger fuse or breaker to solve the problem, BUT that will only increase the hazard, not correct it. Do not follow "bad" advice by installing a larger fuse in a misguided attempt to correct the problem. To install an over-sized fuse would almost guarantee damage to the wiring and an electrical system fire.
Fuses That "Blow" RepeatedlyWithout being able to "hands on" troubleshoot the circuit served by the repeatedly blowing fuse, none of us can identify the specific defect which is causing your problem.Therefore, the following generic answer can be applied to any electrical circuit, whether in a vehicle, or in a building, whether direct current [DC], or alternating current [AC].Fuses [and Circuit Breakers] are safety devices designed and installed in electrical circuits TO PROTECT the conductors [wires] and other components from short circuit conditions and/or overload conditions which cause an extremely large flow of electrical current [measured in Amperes], which causes overheating of the conductors that results in damage to the insulation and the conductors.And in a worst case scenario, the probability of a FIRE which could destroy the vehicle, house, or other structure in which the circuit is located.When a fuse or Circuit Breaker [and replacement fuses, or repeatedly "tripping" Circuit Breakers] "blow," especially if it happens repeatedly, is an indication of an UNSAFE CONDITION in that circuit, usually a short.The fuse or circuit breaker is doing what it was designed, intended, and installed to do, that is to protect the conductors and components of the circuit which it serves.The proper "fix" for this issue is for a qualified technician, who knows what he or she is doing, to troubleshoot the involved circuit, find and identify the defect, and make proper repair [s], BEFORE replacing the fuse again [with the properly sized fuse or before resetting a circuit breaker].Some ignorant few people will suggest installing a larger fuse or breaker to solve the problem, BUT that will only increase the hazard, not correct it.Do not follow "bad" advice by installing a larger fuse in a misguided attempt to correct the problem. To install an oversized fuse would almost guarantee damage to the wiring and the probability of an electrical system fire.
Fuses That "Blow" RepeatedlyWithout being able to "hands on" troubleshoot the circuit served by the repeatedly blowing fuse, no one can identify the specific cause/defect which is causing your problem.It is clear that you have a "short circuit" condition in the horn wiring circuit.The following generic answer applies to any electrical circuit, whether in a vehicle or in a building, or whether alternating current [AC] or direct current [DC].Fuses [and Circuit Breakers] are safety devices designed and installed in electrical circuits TO PROTECT the conductors [wires] and other components from short circuit conditions and/or overload conditions which can cause extreme flow of electrical current [measured in Amperes], and overheating of the conductors that can result in damage to the insulation and the conductors. And in a worst case, the probability of a FIRE which could destroy the vehicle, house, or other structure in which the circuit is located.When a fuse [and replacement fuses, or "tripping" Circuit Breakers] "blow," especially if it happens repeatedly, is an indication of an UNSAFE CONDITION in that circuit, usually a short.The fuse or circuit breaker is doing what it was designed, intended, and installed to do, protect the components of the circuit which it serves.The proper "fix" is for a qualified technician, who knows what he or she is doing, to troubleshoot the involved circuit, find and identify the defect, and make proper repair [s], BEFORE replacing the fuse again [with the properly sized fuse or before resetting a circuit breaker].Some ignorant few will suggest installing a larger fuse or breaker to solve the problem, BUT that will only increase the hazard, not correct it. Do not follow "bad" advice and install a larger fuse in a misguided attempt to correct the problem. To install an over-sized fuse would almost guarantee damage to the wiring and an electrical system fire.