0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How should a trailer's safety chains be attached to the towing vehicle?
Your hitch should have slots designated for the chains.
How do you access trailer hitch wiring in a 2011 Dodge Journey?
under the car,behind spare tire,is the wiring harness with access plug for dodge trailer harness (optional) my came with 2012 journey
What is the main function of boat trailer safety chains?
If the trailer hitch should come uncoupled, the safety chains keep the trailer connected to the towing vehicle. When attached PROPERLY, they will also prevent the tongue of the trailer from digging into the road surface if it should disconnect. Cross the chains left to right, and right to left UNDER the tongue of the trailer.
How do i wire a 98 explorer trailer hitch?
There is an existing plug behind the left side tail light (look up from under the bumper). Get the proper tee-connector and plug it in.
Where is the vin on a holiday rambler camper?
Looking at the front of the trailer, on the right side of the tonge frame rail under the gas. metal tag 1 1/2"x 5".
What type trailer hitch can use to tow a u-haul trailer 6x12 for a Chevy El Camino 4x4?
Measure across the rear frame rails and with that measurement go to a home/auto center and look at the receiver hitches. A receiver hitch mounts to the frame and is very strong.They are not listed for your truck but you can adapt one to fit. Keep in mind any obstacles under your vehicle (spare tire?); you may need to add spacers etc. Once a receiver hitch is in place ( four bolts) you can add a drop/raise tonque to achieve the exact height you need to tow your trailer level. Good luck.
How do you determine trailer hitch height?
First, set the trailer you're towing on level ground...if you have a jack stand w/wheel combination that'd be great! Level the trailer by either using a small level on a central part of the trailer and make adjustments to the level by winding your jack up/down. (It ain't rocket science, so you could eyeball it by standing a good distance from the side.) Measure the distance from the ground to the top of the "ball mount" on the trailer. The Highlander, is essentially a Camry with a SUV body, so your weight/towing limits are modest, compared to a truck for instance. So, what I'm getting at, is the chances are your trailer is under 150# hitch weight...The Highlander shouldn't "squat" too badly when you put the trailer on. Determine where your hitch is located...(I doubt Highlanders have bumper-mounting capabilities, so I'll take a guess and say you have a Class I - perhaps Class II). Measure the distance from the top of the inside of the "receiver" section (where the hitch goes) to the ground. Subtract trailer height from your Highlander measure. That should give you a ballpark measure of between 2-5". Determine your ball size (it's stamped on the tongue of the trailer). Next, GO SHOPPING! I recommend "Wally World", they're more apt to give you money back on mistakes! Buy the measured "drop", if any. Obtain a locking pin or hitch pin and cotter key that fits the hole in the receiver shaft and grab the right size ball as well...Make sure your receiver size is correct! (You'll need a LARGE crescent wrench to mount the ball.) Place the hitch into the receiver and mount the ball and make sure the washers are put on the bolt out of the bottom of the ball in the same order as packaged. Using the receiver as your vise tighten the nut below the ball, hand tight...There's absolutely NO NEED TO BREAK THE WRENCH TIGHTENING THE NUT. If you have any more questions write again. P.S. practice mounting/dismounting the trailer and it's operation in a large open parking lot...If you have someone to help spot the hitch as you back up to the trailer it helps alot. On the tow vehicle, 18" to 20" from the ground to the top of the ball usually puts you in the ball park.
Your van weighs 3862 how much is that in tons?
1 ton is 2000lbs, so it is just under 2 tons.
Longest car trailer allowed to tow with class a RV?
That will depend on the length laws of your state (and any other state you're traveling to). What's just as pertinent is the weight rating - if the addition of the trailer brings the total combined weight rating of the combination over 26,000 lbs, you will need to upgrade your licence to a non-CDL Class B (if the weight rating of the trailer is under 10,000 lbs.) or Class A (if the weight rating of the trailer is over 10,000 lbs.).
What is the towing capacity of a 1989 Pontiac 6000 LE sedan with a class 2 hitch?
Its not really recommended to tow more than 1500 lbs with the A-Body cars (Pontiac 6000, Chevy Celebrity, Buick Century, Olds Cutlass Ciera). Althou they have a good motor, and tranny, they just don't do well under the stresses, and aditonal heat, of pulling a trailer.
Why won't brake lights work on 2000 buick lesabre?
Check all fuses first, check the brake switch located under the dash above the brake pedal. If you have a hitch on the car check the trailer wiring harness.
How do you attach a bike trailer?
First, Determine what type of bike trailer hitch system you have. There are quick-release skewers and fixed-nut attachments. The quick-release skewer is just a squeeze clamp and strap that attaches around the bike seat post. The fixed-nut attachment is a horizontal hole through the trailer hitch that will bolt to the rear bike wheel. Second, Unscrew the nut holding on the rear tire. This is necessary for the fixed-nut attachment bike trailer hitches. Third, Slide the fixed-nut attachment trailer hitch over the rear wheel bolt protruding through the bike frame. Screw the nut back on tightly. Fourth, Wrap the strap around the bike seat post under the bike seat. This is necessary for the quick-release skewer bike trailer hitches. Lastly, Squeeze the clamp on the quick-release skewer. Feed the strap back through the quick-release skewer on the bike trailer. Release the clamp on the quick-release skewer. Pull the strap tight.
