Take it off
A 1999 Hyundai Accent does not have a clutch adjustment. The clutch pedal however, can be adjusted to a different height.
Yes there is a hydraulic clutch on the miata. Just to the outside of the firewall, near the brake master cylinder is the clutch master cylinder and resevoir.
There is a reservoir on the clutch master cylinder, mounted to the firewall toward the driver side. It's got a black cap.
I have been told by Hyundai services that it would cost me $950 to replace the clutch of my 2000 Hyundai accent. I think this is a reasonable price.
If it does not have a Hydraulic clutch, then it has no fluid. If it has a Hydraulic clutch the clutch master cylinder is normally located on the firewall, driver's side, near the brake master cylinder.
there is no clutch cable. it has a hydraulic clutch. there will be a clutch master cylinder on the firewall near the brake M/C. a hydraulic hose will connect that to the clutch slave cylinder on or near the tranny. the slave cylinder pushes on a fork (lever) that disengages the clutch.
The clutch slave cylinder , for a hydraulic clutch , is inside the manual transmission bellhousing
The clutch slave cylinder for a hydraulic clutch is inside the manual transmission bellhousing
There are two normal causes. The clutch is worn out or there is a leak in the hydraulic clutch slave or master cylinder. To check the clutch, press the clutch slave cylinder down. If the clutch slave cylinder bellows compresses down to the slave cylinder, the clutch is worn out. Check the clutch master cylinder fluid level. if this is low, then the clutch cylinder need to be checked. To check for a hydraulic leak in the clutch slave cylinder, remove the cylinder's bellows and check for any fluid. If fluid is present, rebuild or replace the cylinder and bleed the system. To check the clutch master cylinder, check the back the of clutch master cylinder for leaks. If fluid is present, replace or rebuild clutch master cylinder and bleed the system. In my experience, hydraulic leaks occur at the clutch slave cylinder.
It's a hydraulic clutch ( the clutch fluid reservoir is near the brake master cylinder )
The slave cylinder for your hydraulic clutch is located inside the manual transmission bellhousing
The clutch master cylinder is in the engine compartment and the slave cylinder for the hydraulic clutch is inside the manual transmission bellhousing
Hydraulic clutch on that model is not ajustable. You either have a bad clutch slave cylinder, Or the clutch and pressure plate needs replaced.
Cable clutch - when you depress the clutch lever or pedal, you pull at a Cable whose other end is attached to the fork that operates the pressure plate in the clutch assembly. Hydraulic clutch - when you depress the clutch lever or pedal, you push at a piston in a Master cylinder. Pushing at the piston pressurizes the hydraulic fluid in the master cylinder, and in the hose leading to a Slave cylinder placed at the clutch. The piston in the slave cylinder extends and operates the pressure plate in the clutch assembly.
The slave cylinder is a hydraulic device that acutuates the clutch. As you depress the clutch pedal it's movement sends hydraulic pressure to the clutch to release it. It's like stepping on the brakes only withe clutch.
Either the clutch master cylinder or the clutch slave cylinder or the clutch hydraulic lines are leaking.
With assist from your foot, the brakemaster cylinder sends hydraulic brake fluid to each wheel to operate the brakes. There is also a clutch master cylinder formany standard shift vehicles. This clutch master cylinder, with assist from your other foot, sends hydraulic fluid to the clutch slave cylinder to operate the clutch throw out bearing.
www.hasport.com has clutch master cylinder adapters. Here is the info from their page: "The new master cylinder adapter allows the use of a Honda-style or Wilwood clutch master cylinder to convert a cable transmission vehicle to a hydraulic setup."
Most automotive clutch systems use brake fluid in the master cylinder. Hydraulic oil would ruin those systems.
Hydraulic and the slave cylinder is in the bell housing.
Hydraulic clutch? Maybe a bad rear seal in the clutch master cylinder
The slave cylinder for your hydraulic clutch is inside the transmission bellhousing
The hydraulic clutch slave cylinder is inside the manual transmission bellhousing