0
During a typical power plant startup, all components of the power plant are started slowly. The turbine is first rolled at a slow rpm. Then the rpm is increased gradually to a point where it can match the frequency of the grid. At this point, the turbine can be synchronized with the grid and start outputting electricity into the grid.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Explain why interrupts are not appropriate for implementing synchronization?
Because they are completely unrelated things? Synchronization can be implemented with semaphores or mutexes.
What is difference between radial flow turbine and axial flow turbine?
in a radial flow turbine the steam enters the turbine in the direction of its radius and leaves it in the direction of the axis of the shaft. in a axial flow turbine the steam enters the turbine in the direction of the axis of the shaft and leaves the turbine in the same direction.
How do you spell turbine?
Turbine is the correct spelling.
Why would you not heat the steam coming out of turbine and feedback to turbine?
becouse this steam is use repetdly for the turbine
Why draft tube is used in francis and kaplan turbine and not in pelton turbine?
The Kaplan turbine is a newer, more revolutionary version of the Francis turbine, which came before it. The draft tube is used so that the turbine does not need to be where the water flow is lowest.
What do you mean by synchronization in operating system?
synchronization mean arrange all process in sequence for that not occured no colusion in the system.
What is turbine home load?
After Synchronization we need to maintain many things like: - Frequency - Power Factor - Voltage - Current If any of these not maintained then the unit will come in Home Load. Home Load is actually a small amount of load (min 2 MW) for a short duration of time (say 2hrs). In these short duration there is need of synchronization again so that the turbine wont tripped. If there is delay than the unit will get tripped & turbine need to roll again and then synchronized. Avinash Rao
What is a synchronization process mean?
a synchronization manager is a program that can help you synchronizing for ex your computer and a palm The process by which files and programs are transferred between PDAs and PCs.
What does the code 54 mean for a 1992 Plymouth Voyager?
I believe that a 54 code is for Turbo only. It may be the synchronization pick up circut. It is not showing a distributor synchronization signal.
What does Wind Turbine mean?
A wind turbine is like a giant fan that produces energy from the wind
The provision of mechanisms for process synchronization?
The provision of mechanisms for process synchronization
What do you mean by whirl velocity of turbine?
Whirl velocity of a turbine is determined by how fast the turbine can turn when it is moving. This is a factor considered with airplane manufacturing. Whirl velocity is the number of times in a second that a turbine can rotate, moving at a given speed.
When was Transactional Synchronization Extensions created?
Transactional Synchronization Extensions was created in 2012.
What does it mean when a signal is self clocking?
In telecommunications and electronics, a self-clocking signal is one that can be decoded without the need for a separate clock-signal or other source of synchronization. This is usually done by including embedded synchronization information within the signal, and adding constraints on the coding of the data payload such that false synchronization can easily be detected.self-clocking-signal
What does it mean when a signal is self-clocking?
In telecommunications and electronics, a self-clocking signal is one that can be decoded without the need for a separate clock-signal or other source of synchronization. This is usually done by including embedded synchronization information within the signal, and adding constraints on the coding of the data payload such that false synchronization can easily be detected.self-clocking-signal
Why current is not concidered while synchronization?
current is load dependent,after synchronization only current will flow
What is mark 6 control system?
MARK6 is used for the protection of steam and gas turbine in electrical generators and process plant applications The main function of Mark6 turbine control system are: -speed control during turbine start up -automatic generator synchronization -turbine load control during normal operations on the grid -protection against turbine -protection against turbine over speed on the loss of land The mark6 system is available as a simplex control or a triple modular redundant (TMR) control with single or multiple racks, and local or remote I/O. The I/O interface is designed for direct interface to the sensors and actuators on the turbine, to eliminate the need for interposing instrumentation, and to avid reliability and maintenance issues associated with that instrument. NOTE : to obtain a highest reliability, MARK6 uses a TMR architecture with sophisticated signal voting techniques.
