0
What does an error code with a spanner icon followed by -19 which flashes on the odometer of my diesel Mercedes ML 270 4WD mean when I turn on the ignition?
Wiki User
∙ 14y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Reset maintenance light on Lexus rx330?
While your ignition is own reset your mileage to the total mileage. Turn the ignition off and then back on while holding in the odometer button until the maintenance light flashes several times and resets.
How do you reset the service light in a Volvo V70?
S70 and V70 and C70 and XC70 1. Press and hold odometer reset button. 2. Turn ignition switch to Run. 3. After SRL flashes, release odometer reset button. 4. Confirm by turning your Volvo off, then on again.
Loss of power and edc light flashes on and off Mercedes sprinter?
Edc Mercedes sprinter
Fuse flashes on odometer on 2001 dodge neon?
The iod fuse under the hood is loose or blown.
How do you get the codes out of a 1990 dodge ram 250?
Cycle the ignition on/off/on/off/on and count the flashes of the check engine light. A pattern of two flashes, pause, two flashes would be a code 22.
Check engine code 1990 Mazda 323?
1990 Mazda 323:The check engine light intermittently flashes a series of long and short intervals. A long flash is followed by 5 short flashes. Then another long flash is followed by 7 short flashes, a pause, and 9 more short flashes. How should I interpret this code?
Not the check engine light but the service light on the 1998 s60 Volvo?
Volvo 1999-2000 - S / V / C70 Models * Press and Hold odometer reset button * Turn ignition switch to "run" position * After SRL flashes, release odometer reset button * Turn ignition off * Turn ignition back on to confirm reset Volvo 1998 - S80 Models * Turn ignition switch to position 1 * Press and hold the odometer reset button * Turn ignition switch to position 2 * Wait until service light blinks and then release odometer button Volvo 1999-2000 - S80 Models * Turn ignition switch to position 1 * Press and hold "day counter reset button" * Turn ignition switch to position 2 * Continue holding day counter for approx. 10 seconds * After SRL flashes, release day counter button * Should hear "beep-beep" to confirm command accepted Volvo 2001 - XC 70 Models * The following steps must be completed with no longer than 5 seconds between each step: * Make sure the trip meter is in T-1 * Turn ignition key to position 1 * Press and hold trip meter button until zero is shown * While still holding the trip meter, turn key to position 2 * When original trip mileage returns, release the trip reset button * Turn key to off
How do you get engine codes from dodge Dakota?
On newer models, about 1997 and later, you need a diagnostic scan tool such as an OBDII that will connect to the engines control module. These are available for purchase at most auto parts stores, starting at around $60.On some older models, you can cycle the ignition as follows to get fault codes:Cycle the ignition twice from ON to OFF, then back to ON within 5 seconds. The check engine light will flash any two-digit codes that are stored in memory, starting with code 88 (8 flashes, followed by 8 flashes). When the list of codes is finished, code 55 will be flashed (5 flashes followed by 5 more flashes). A list of codes can be found in either a Chilton's or Haynes repair manual for your model year, or probably available from your Dodge dealer. Or, just ask above.
How do you find the fault codes on your 1995 grand caravan?
Turn the ignition key on,off,on,off then on and count the the flashes of the check engine symbol .It flashes the first number then there is a short pause then it flashes the second number. Example 24 ( two flashes and a pause then four flashes). Look up this number in Chilton's/Haynes or the shop manual for the vehicle
Why does the security light stay blinking on your 2004 keyless entry Camry Toyota after you turn off the car?
The security light flashes when a programed key is not installed in the ignition, when you insert a programed immobilizer key in the ignition the security light will go out, the light flashes as a theft deterrent
How do I reset the maintenance light in a Toyota Yaris?
The system must be reset after the engine oil replacement. Reset the system by the following procedure: 1. Turn the ignition key to the "OFF" position with the trip A reading shown. 2. Turn the ignition key to the "ON" position while holding down the trip meter reset knob. Hold down the knob for at leat 5 seconds. The indication light flashes and the bars displayed in the odometer disappear gradually. The odometer indicates "000000" and the light goes off. If the system fails to reaset, the light will continue flashing. "
Where can you find lost Bose radio code for Mercedes Benz ML320 1999?
why does the bose stereo flashes code
