== == "Negative 1" refers to the position of the baby's head in relation to your cervix. Negative numbers imply that the baby's head is still floating above the cervix. Zero position means the baby's head is engaged. Positive numbers means the baby's head has begun its descent through the cervix and into the birth canal. The higher the negative numbers, the higher up in your uterus the baby is located (ex., - 3 is higher up than - 2). The higher the positive numbers, the lower into the birth canal the baby is located (ex., +3 is lower -- closer to birth -- than +1).
Your cervix has thinned out 60%
It means that only 20% of the humidity of 100% is in the air.
Your cervix must dilate (open up) to 10 centimeters before you can essentially, 'push' the baby out. So half a cm is good progress, though it seems a bit early at 29 weeks? 75% effaced: you have to be 100% effaced (thinned out) for the cervix to fully dilate & ready to deliver the baby. So you're just about finished there.
50% is out of 100% which means your cervix is paper thin. Once your cervix is dialated to 10cm & your 100% effaced baby is ready to be born. How long it could be in this position, depends on your body.
*80% effaced and -2cm station.
it mean that person not in the stage of disease which shows symptoms but he has organisms in body which cause disease. if the number of microorganism is increased 40 percent, it shows symptoms OR, it could apply to the childbirth process. Basically how much the cervical opening has pulled back or thinned. But this is also tied to how much the cervix has dilated, or opened up to allow the child to be born. Fully dilated is 10 cm.
The cervix dialates during the course of labor. This is measured in centimeters across (from 1 centimeter to 10 which is completely dialated.) In addition to opening up (dilatation), the cervix also thins out (effaces) this is measure in percentage from 10% to 100% effaced. As labor progresses, the uterus enlongates and the cervical tissue is drawn up into the body of the uterus, similar to the forskin of a penis being incorporated into the shaft during an errection. following a routine labor vaginal exam, the MD might state: : "she's 3-4/40% and -2." this means 3-4 centimeters in dilatation, 40% effaced (and the presenting part of the fetus is 2 centimeters above the ischial spine which describes how far down the baby has come)
You don't have to be effaced or dilated to go into labor. But this could mean u will be waiting for the bundle of joy little longer! Good luck!
The meaning of this verb can vary depending on the context. It can mean to erase a mark from a surface 'Molly effaced the mark off her surface'. It can also mean becoming inconspicuous and insignificant. For instance, 'Anna effaced herself'.
== == Your cervix prepares for birth by softening and thinning, or effacing. You won't feel this sign of labor happening. Instead, your health care provider will check for signs of cervical change with vaginal exams. Effacement is often expressed in percentages. When you're 50 percent effaced, your cervix is half its original thickness. Your cervix must be 100 percent effaced, or completely thinned out, before a vaginal delivery
80% effaced_ Happy birthday mommy go to the hospital
Sometimes you will take the absolute value of the percent error because your estimated number could be less than the theoretical, meaning the calculation is negative. But an absolute value is always positive. A percent error can be left as a negative though, and this would be perfectly acceptable (or even preferred) depending on what you're doing.Answer:In the sciences, a negative percent error indicates a low result. If you have a 0% error, then your observed (lab) result was exactly the same as the theoretical result. A 5% error could mean that your observed result was a little high. A negative percent error is possible; if your observed results were lower than the expected, then you would have a negative percent error. A -5% error could mean that your results were a little low. Having a negative percent error isn't worse than positive percent error -- it could mean the same thing. If you were to have a choice in having a 20% error and a -5% error, the negative percent error is more accurate.