Want this question answered?
Flux is used to bond soldered metals together. The flux is spread onto both pieces of metal that will be soldered. If the metal is a wire, spread the flux on the metal part of the wire. Then heat the solder and place the two pieces being soldered together with a tongs or the tip of the soldering iron.
you dont .thats what the flux does.solid core wire needs gas
Yes, for as long as the magnetic field is moving along the conductor. A static magnetic field will not induce current, a dynamic field is required.
Strip the wire to desired length. Then hold the wire horizontally and hold the soldering iron underneath the stripped part while holding the solder on the top of the wire. When the wire gets hot enough it will suck the solder into the wire
The term flux means to clean. Not all welding processes use a flux. Stick welding electrodes contain fluxing agents. MIG hard wire doesn't but flux-cored MIG wire does. TIG does not as the rods are bare. Most brazing applications require flux. Gas welding usually doesn't except for certain metals.
pre tinning make it easier to solder wire because the solder is already " stuck" to the wire. and less solder will be needed to join the wire. if you watch the solder under a magnifier while tinning, you will notice the solder does not flow and "stick" until proper heat and flux ar applied. this heat usually is more than required to melt the solder because it takes mor heat to heat up the wire due to higher density. after tinning, less heat is required to melt the solder, and enough flux is usually left from tinning to quickly join the wire to the desired material provided the material is also tinned. this reduces cold solder and provides for a more relible connection. To tin the wire first is to cover the end of the wire with a layer of solder before you put it thru the hole in the PCB that will give you insurance of a proper electrical contact else you will put a heap of solder on the PCB without a proper contact with the wire itself what is called a dry joint that go for un tinted copper wire only normally all electronic component pins is factory tinted
Flux is used to keep metals from oxidizing. Solder will not bond well with copper-oxides which are formed when copper is exposed to high temperatures (ie a soldering iron) the flux prevents the oxidation. If you were to solder without flux the solder joint would be weak and possibly completely nonconductive.
Flux is used to bond soldered metals together. The flux is spread onto both pieces of metal that will be soldered. If the metal is a wire, spread the flux on the metal part of the wire. Then heat the solder and place the two pieces being soldered together with a tongs or the tip of the soldering iron.
Solder is a group of metallic alloys that melts at a relatively low temperature and is generally used to connect other pieces of metal together. The low melting point makes it useful for some applications, especially electronic circuitry and some plumbing applications, though it should be noted that plumbing solder is a different alloy than electronic solder and plumbing solder has little or no lead to minimize lead exposure to the people who drink the water. Having described what solder IS, soldering wire is just that, its a wire that is made of solder. Solder wire is useful when working on electronic circuits since it allows the user to control how much will be put on an electronic connection. Solder wire comes in several sizes, as well as with or without a flux core. Flux is a material (usually either acidic or rosin) that encourages melted solder to flow onto other metals, usually copper, iron or brass. Other types of solder are available for use on materials such as aluminum, but solders should match the application to match the type of metals you are joining.
To facilitate the soldering process, a chemical material called flux can be used to remove oxidation from the surface, keep the air from oxidizing the surfaces during soldering, and to aid in the flow of solder through the joint. Fluxes can be found within the solder (cored solder) or separately in paste form.
Yes it can. I use flux core wire because there is no need for gas with flux wire.
Answering "For what type of fitting would the application of solder wire during the jointing process be required intgral ring or capillary or type a or type b?"
Solder the wire.
Flux is used to solder gold plated jewelry. Flux can be used on other metals as well. All metals should be cleaned, and chemical free before soldering.
Welder slag is a byproduct resulting from the welding process, often forming a layer on top of the welded joint. It consists of the residue from the flux used in the welding rod or wire, which helps protect the weld pool from impurities and contaminants while it cools. Slag is typically removed after welding to inspect the quality of the weld and ensure proper fusion.
you dont .thats what the flux does.solid core wire needs gas
Solder will conduct electricity, so is not an insulator.