0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you bleed the heater core?
If by "bleed" you mean drain, disconnect the lower of the two hoses (do not confuse with the pipes from the AC evaporator) and drain the coolant into a bucket. If you are flushing the system (which you should if you are changing the coolant anyway), dont bother draining it, most of the coolant will flow out anyway, just do the coolant flush and fill from the radiator.
How do you bleed the air out of the fuel system on a 1992 maxima?
you dont have to it does it itself
If your hydraulic fluid leaks out and you refill it do you need to bleed the system?
I dont no
How do you bleed the coolant system on a 1997 buick skylark?
you dont The cooling system has lots of nooks and crannies that trap air, making it difficult to fill the system with coolant. The fill cap and neck are supposed to be at the high point of the system to help air bleed out, but often they aren't. And even if they are, you need all the natural help you can get. So jack up the front of the car, which gets the coolant fill neck as high as possible. Check for air bleeds on the engine. Sometimes you'll see an obvious air bleed, such as a bolt-like item threaded into a hose. If there's an air bleed, open it. If there are several, open them all. If you have access to a factory service manual for your car, check it for a coolant fill procedure. Your owner's manual should list location of bleeder valves. Pour in the required amount of coolant slowly until you see coolant oozing out of the open air bleeds. Then close the bleeds and top off the system with the remaining coolant. If the system has a heater coolant valve, close it by moving the temperature control lever or knob to cold. With the engine running at fast idle and warmed up, have a helper move the lever or knob to hot while you listen at the coolant valve. If after the first rush of coolant you hear a continuous gurgling noise, there's still air in the coolant, and you need to open the bleed valves again. Be prepared to watch the coolant level in the reservoir over the next few weeks.
How do you bleed the cooling system on a 1995 Lincoln?
you dont bleed cooling systems you have to take it to a mech. shop or have the proper equipment and the r-134a on hand to do it your self.
How do you bleed the cooling system on a Saab 9-3 Tid?
i dont think you really have to do that. Double check with the dealer
Where is the air bleed valve for the cooling system on a 95 Mercury Villager?
bleed a 94/95 Villager coolant systemThere are accually three. One is on the right side of the radiator, another on top of the intake manifold and a bleed tube which is capped, its located about a foot left and a foot below the brake master cylinder. You can't see it but you can reach down and feel a 1/4 tube with a rubber cap on it. if you need to bleed the coolant system you must first loosen the bleed plug on the radiator and fill the radiator until coolant startes to come out then tighten that bleed plug, next loosen the plug on top of the manifold and squeese the upper radiator hose to explell air out the intake bleed plug while adding coolant to the radiator. This will take several attempts.once coolant come out steady from the intake bleed port, tighten the plug. Next On the bleed tube remove the cap and use a piece of wire to stick inside the tube to make sure its open then slide on a three foot clear rubber hose on the bleed tube and run the other end to your overflow tank making sure its submered in the coolant. Next you must modify the radiator cap by take a coat hanger and cut about a 1 inch piece, bent it in a u a slide it between the spring and popit valve, this willkeep the system from pressurizing. Now Start the eng, turn the heater or heaters on max hot. Run eng a about 25oo rpm until fan comes on and contue until no more air is seen coming thru tube. This could take 10 minutes or so. Then top off the radiator with coolant. Dont forget to remove the coathanger from the cap.also remember to remove the clear hose from the blled tube and reinstall the cap. Good luck
How do you tell if the clutch master cylinder is gone out on a 87 king-cab Nissan truck?
first check your clutch slave cylinder for leaks, if its leaking ,replace and bleed system,if its not leaking,bleed system ,dont forget to bleed clutch damperand if its still not right, then replace clutch master cylinder.
Where is the evaporator on a home air conditioning system?
i dont believe they have one but dont take my word I don't know if it is called an evaporator, but somewhere in the part of the unit that is inside the house are some coils full of coolant and a fan that blows air over the coils . This is where the coolant evaporates and cools the air. The coolant is then carried outside and compressed to make it give up the heat .
Do you need to bleed air out of the system when you change antifreeze and flush a 1996 Corolla?
yes you do cuz if you dont you will not get the air pockets out and then your radiator fluid could be to low no
When you add thermal energy to a system what will happens to the kinetic energy of the molecules within the system?
if you add a thermal energy to a system then it will happens nothing because u dont no anything
What happens when you put oil in the liquid cooler tank of a 50cc motorcycle by mistake.. does it ruin your bike?
as long as u dont run it to long, just dump the coolant and oil flush sytem refill with new coolant and you should be good to go
