Want this question answered?
Multiply the current by the voltage: 120 times 0.3, which is 40 watts.
The U.S. 60 Hz bulb should be useable in the United Kingdom. Even though the U.K. uses 50 Hz bulbs, this small difference in frequency should not matter.
LED's (Light Emitting Diodes) work on DC current, not AC, so the AC needs to be stepped down to an appropriate voltage via a transformer (probably only a few volts), converted to DC via a rectifier and filter (to smooth out the ripple current). there are a constant driver in side the 120V AC led light bulb , this driver transfer the AC to DC, so the led could work with DC.
We put one of these in a light fixture with a dimmer. It didn't dim, but just went on and off. However, a couple of months later it went out and the house was filled with a electrical stink. My guess is the directions may have told me not to hook it up to a dimmer and I didn't notice it.
Okay so I searched for 3 hours on Google and no answer so here it is: 40W - 110C; 60W 140C; 100W 136C; and 100W Flood (Red Green Yellow) 125C. Standard bulb, 117VAC, 60Hz, facing up (edison Base down, free air, 22C ambient, measured with K-type thermocouple, calibrated in last 12 months....
HELICAL 13W 120VAC 60Hz 180mA13W means 13 watts cfl...... =40 watt incadescent.
When you put a light bulb in series with a inductor, the inductive reactance of the inductor reduces the current available to the light bulb, making it less bright. For this effect to be noticed, however, you need a very large inductor. To cut the current in a 60W bulb at 120VAC/60Hz by one half, for instance, you need an inductor around 0.6 henrys.
If you can use it in your lamp it will be a 20 watt bulb
Multiply the current by the voltage: 120 times 0.3, which is 40 watts.
The U.S. 60 Hz bulb should be useable in the United Kingdom. Even though the U.K. uses 50 Hz bulbs, this small difference in frequency should not matter.
There are 1350 watts in a 60 hz bulb. There is a push not for everyone to transfer to led bulbs.
LED's (Light Emitting Diodes) work on DC current, not AC, so the AC needs to be stepped down to an appropriate voltage via a transformer (probably only a few volts), converted to DC via a rectifier and filter (to smooth out the ripple current). there are a constant driver in side the 120V AC led light bulb , this driver transfer the AC to DC, so the led could work with DC.
We put one of these in a light fixture with a dimmer. It didn't dim, but just went on and off. However, a couple of months later it went out and the house was filled with a electrical stink. My guess is the directions may have told me not to hook it up to a dimmer and I didn't notice it.
Lights at home are connected in parallel. (Switches are connected in series with the lights in order to turn them on and off.) This way, each light receives the same voltage. Placing the lights in series would divide the voltage between the lights, reducing the power of each, and it would have the effect that one light burning out would cause all the others on the same circuit to stop working.
An electronic component of floor lamps sold by Home Depot that have a two-bulb 120v fixture on the top and a single bulb 12v fixture on a flexible arm. These may not be very reliable as the circuit board failed on mine in less than two years of light-duty service.
I own a 4' Fiber Optic Tree. Inside the base, at the bottom, center, is a one piece light and refractor. 2 screws hold light down. Light is approx. 1 1/2" wide. I bought a replacement bulb at the Home Depot. Bulb 20watt,22va,60hz. Good Luck.
a fuse bulb is a bulb in which the filament of the bulb burns and it stops working