0
pinagdugtong na madaming amplifier
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What are the steps involved in finding the signal gain for a common-emitter BJT amplifier?
The signal gain of a CE BJT amplifier is hFe or collector resistance divided by emitter resistance, whichever is less.
How do you design a RC coupled bjt amplifier using pnp transistor?
same as you would using an NPN, except the supply voltages are reversed
Explain Ri and Ro effect the performance of bjt voltage amplifier?
aries.ucsd.edu/NAJMABADI/CLASS/ECE65/06-W/NOTES/BJT3.pdf
Minimum proper base emitter voltage at any instant?
The base-emitter voltage of a BJT is dependent on temperature and current. The minimum voltage ranges from 0.6V to 0.7V. Anything less, and the transistor goes into cutoff. As far as "proper voltage" is concerned, it is more correct to say "proper current", because that is the basis for the BJT - it is a current amplifier, not a voltage amplifier. The proper current depends on the particular biasing design of the circuit at hand.
Why electrolytic capacitors are used for frequency response of BJT as amplifier?
It can take a lot of capacitance to present a low impedance to a low frequency. Electrolytics offer lots of capacitance for a low price.
Who is more gain amplifier cascaded amplifier or darlington amplifier?
Darlington amplifier has more gain when compared to cascade amplifier .
What is the configuration of cascade amplifier?
In a cascade amplifier, two identical or non identical amplifiers are cascaded ,i.e., connected in series through a capacitor. They are mostly common emitter amplifiers that are cascaded together.The final gain of the cascaded amplifier is the product of the first amplifier's gain and the second amplifier's gain. However, the bandwidth of the cascaded version becomes lesser than the individual gains.
What are the steps involved in finding the signal gain for a common-emitter BJT amplifier?
The signal gain of a CE BJT amplifier is hFe or collector resistance divided by emitter resistance, whichever is less.
Which bjt transistor amplifier can be used as a voltage buffer?
the common collector can use as voltage buffer
What is the explanation for the working CE BJT amplifier?
In electronics, a common-emitter amplifier is one of three basic single-stage bipolar-junction-transistor (BJT) amplifier topologies, typically used as a voltage amplifier. In this circuit the base terminal of the transistor serves as the input, the collector is the output, and the emitter is common to both (for example, it may be tied to ground reference or a power supply rail), hence its name.
What is the expected amplification of a BJT transistor amplifier if the dc supply is set zero volts?
very simple, zero.
Why use a npn transistor in a common emitter bjt single stage amplifier circuit?
You can use an npn or a pnp bjt in a common emitter amplifier circuit. The decision of which one to use is based on whether you want the collector and base to be more positive (npn) or more negative (pnp) than the emitter.
How BJT works as a amplifier?
aplied weak input signal is amplied at output side due to very high resistence
Which BJT amplifier has the phase shift between input and output voltage is 180 degree?
The Class A common emitter BJT design has input on the base and output on the collector. This design is inverting, or 180 degrees phase shift.
How do you design a RC coupled bjt amplifier using pnp transistor?
same as you would using an NPN, except the supply voltages are reversed
What does gm0 represent in a BJT amplifier circuit?
gm0 is not used in BJT amplifier circuits; it is used in JFET circuits. It is the transconductance at zero gate bias. Since the transconductance varies as the bias is varied, this gives a benchmark level at a given defined point, and other transconductances can be calculated from it as a function of the amount of negative bias on the gate. If it were linear it would be the same everywhere, but it is not.
Explain Ri and Ro effect the performance of bjt voltage amplifier?
aries.ucsd.edu/NAJMABADI/CLASS/ECE65/06-W/NOTES/BJT3.pdf
