0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
When air is on it makes a load whining noise?
Bad bearing in compressor? Bad bearing in compressor?
How do you tell if the compressor is bad in a window air conditioner?
Borrow a clamp on amp meter and check full load amps. If pulling full load amps then compressor condemned.
Why flywheel is used in reciprocating compressor not in centrifugal compressor?
Flywheel prevents fluctuation in the speed of the motor as a result of load fluctuation. It stores the energy and dissipates it to the compressor for prolonged period. So the load fluctuation which is high during compression stage and low during other stages during a cycle in reciprocating compressor gets nullified. On the other hand, centrifugal compressor continiously compresses the gas and does not have load fluctuations, hence flywheel is not required.
What does rla mean on an air compressor?
Rated load amps = rla
What instrument is used to check the full load amps of a compressor?
amprobe
You want to run power from your home you have a 200 amp in the house to a garage that you recently built you have 110 and 220 outlets The only 220 you plan on running is a small air compressor What?
The voltage for the air compressor is needs to come from a double (two) pole breaker. The size of the breaker needs to be 250% of the full load amps of the compressor. The wire size to the compressor has to be 125% of the full load amps of the compressor.
Does compressor work more efficiently with an increased head pressure?
It depends on other conditions too. There is a net suction head, which is the pressure from which the compressor is drawing the gas. An increase here will often improve the compressor's efficiency. There is also a net discharge head, which is the pressure the compressor is trying to maintain. An increase here will often decrease the compressor's efficiency. There is an efficiency curve for all compressors, and they are all different based on their design, it is dependent on the differential pressure (NDH - NSH) and load (air flow in SCFM, typically) of the compressor, at a certain load the efficiency peaks then drops as the load increases.
Does car air conditioning use fuel?
The air conditioning compressor is belt driven from the engine. While compressor is on it adds another load to the engine. Therefore; yes it does require additional fuel to be used to compensate for the additional engine load.
What do you mean by loading and unloading of compressor?
Most air compressors do not have a continuous load, as a result there is a need to control the amount of air entering the system. One way to allow for load swings is to let the air surge tank pressure float between two pressures. To do this you can either start and stop the compressor automatically to stay with in the required pressure range. Say pressure Pmin and Pmax. During normal requirement(load) of air, compressor will work at below Pmax.But when the requirement(load) decreases, delivery pressure start to increase. And when pressure equalise to Pmax,compressor start to unload(means pressure of the compressor start to decrease). During unloading air inlet valve is closed and delivery pressure decreases till it become equal to Pmin. Working of compressor in this phase is known as unloading. As soon as pressure become equal to Pmin compressor start to load again till it reaches Pmax. working of compressor in this phase is known as loading.
What type of load is a 3 phase compressor motor?
In electrical terms a three phase compressor is a compressor that is driven with a three phase motor. There are compressors that have three pressure heads. The three heads boost the pressure up in higher increments but these are referred to as three stage compressors.
How do you stop the second compressor in a 7.5 ton dual compressor unit from cycling on and off every 10 seconds?
I assume that it is an air compressor (dual units - two compressor motors) used to provide pressurised air to operate some valves and devices in a industrial plant. (Because it is not clear in the question) Normally the compressor is designed to operate in "load and unload " mode through few solenoid valves, if not equipped with Variable frequency Drive. If the compressor is equipped with variable frequency drive, then it is designed to run in "load and Unload" mode using the VFD for variable speed to switch between load and unload mode. In both the cases, load and unload mode are trigged by pressure switches or pressure transmitters at a preset differential values. Air compressor runs on "load" mode till pressure reaches the preset maximum value. It then switches to "unload" mode till the pressure reaches the minimum preset value. Once the minimum value is reached, it switches again on "load" mode. The cycle continues, but motor does not start - stop during these modes. Air pressure is a function of consumption in the usegae points, which keeps on reducing gradully basis the consumption. How quickly or slowly the pressure reduces - depends on the rate of air consumption. There could be several reasons for the second compressor to go on - off every 10 second. Check the "load - unload" pressure setting on the conmpressor. Increasing the differential setting a bit more, will increase the on-off cycle time. Check the requirement and data sheet before doing so. Check the consumption, whether it is genuine or waste (air Leakage). Check what is happening the first compressor. If it runs on "load" mode all the time then the actual consumption is just more than the capacity of the one compressor, hence the second one comes on but goes off every 10 seconds, since the consumption is just slightly above the first compressor capacity. If the waste or leak can be arrested, only one compressor can manage the load, most of the times. Check the control philosophy the compressor, whether it is designed to go on - off or it is designed to switch between load and unload mode - corresponding to differential pressure setting. (Generally Load and unload mode does not turn the motor on and off, but during unload mode, it keeps running at almost no load current and during load mode it takes normal load current)
Ac compressor squeals when ac is not on but is quiet when ac is on?
it is probably the bearings going out in the ac compressor pulley or belt slippage. the reason it is different when it is on is because the belt is not under "load" or has resistance.
