Want this question answered?
Following are the essentials of indicating instruments: 1. Operating torque, 2. Controlling torque, and 3. Damping torque. OPERATING TORQUE Operating torque is produced by making use of any of these effects: magnetic, electromagnetic induction...., it is required to move the moving system of the instrument. CONTROLLING TORQUE Controlling torque opposes the operating torque and increases with the deflection of the moving system. It ensures that the deflection of the pointer is according to the magnitude of electrical quantity being measured. If this torque were not provided, the pointer would continue to move indefinitely and the deflection shall be independent of electrical quantity being measured. It also bring the pointer back to zero when the instrument is removed from the circuit. This torque is either obtained by spring or by gravity. In spring control, one or two phosphor bronze spiral hair-springs are attached to the moving spindle. The other end are attached to the frame. In this case Tc proportional to Angle of deflection. In gravity control, a small weight is attached to the moving system in such a way that it tries to bring the pointer back to the zero position when it is deflected, due to gravity. In this casse Tc proportional to sine of the angle of deflection. DAMPING TORQUE Controlling torque controls the deflection and tries to stop the pointer at its final position where its Td = Tc But due to inertia, the pointer oscillates around its final position before coming to rest. Hence damping torque is provided to avoid this oscillation and bring the pointer quickly to its final position. Thus the damping torque is never greater than the controlling torque. In fact it is the condition of critical damping which is sufficient to enable the pointer to rise quickly to its deflected position without overshooting.
Megger Group Limited was created in 1889.
I did them with a 1,000 volt megger .
It is the terminal on the megger that the ground cable connect to when testing a device to ground.
yes
Following are the essentials of indicating instruments: 1. Operating torque, 2. Controlling torque, and 3. Damping torque. OPERATING TORQUE Operating torque is produced by making use of any of these effects: magnetic, electromagnetic induction...., it is required to move the moving system of the instrument. CONTROLLING TORQUE Controlling torque opposes the operating torque and increases with the deflection of the moving system. It ensures that the deflection of the pointer is according to the magnitude of electrical quantity being measured. If this torque were not provided, the pointer would continue to move indefinitely and the deflection shall be independent of electrical quantity being measured. It also bring the pointer back to zero when the instrument is removed from the circuit. This torque is either obtained by spring or by gravity. In spring control, one or two phosphor bronze spiral hair-springs are attached to the moving spindle. The other end are attached to the frame. In this case Tc proportional to Angle of deflection. In gravity control, a small weight is attached to the moving system in such a way that it tries to bring the pointer back to the zero position when it is deflected, due to gravity. In this casse Tc proportional to sine of the angle of deflection. DAMPING TORQUE Controlling torque controls the deflection and tries to stop the pointer at its final position where its Td = Tc But due to inertia, the pointer oscillates around its final position before coming to rest. Hence damping torque is provided to avoid this oscillation and bring the pointer quickly to its final position. Thus the damping torque is never greater than the controlling torque. In fact it is the condition of critical damping which is sufficient to enable the pointer to rise quickly to its deflected position without overshooting.
The weston type galvanometer is a moving coil galvanometer in which a pointer is attached to the coil for measuring deflection due to torque .
It is measurement done by megger tool of measurement .
Tighten the belt until you have 1/2" of deflection at midpoint. I hope this helps you. Mark
Torque is the cross product of radius and force .Torque is a twisting effect. Torque is the cross product of radius and force .Torque is a twisting effect.
Torque=pQ(Vt1R1 - Vt2r2)
Megger Group Limited's population is 1,500.
megger are available in ac &dc
I did them with a 1,000 volt megger .
Megger Group Limited was created in 1889.
I do not know of a CHART, but the equation is: (Torque X RPM) / 5252 = Horsepower.
torque/weight ratio of an instrument indicates sensitivity.if a pointer is having less weight, it will be having high torque/weight ratio so that even for a very small deflection pointer starts moving and indicates measured value.