0
ambot
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How many significant figure are in 23.70?
4, assuming the last zero is an indicator of precision.
How many significant figures in 1.40?
3. The last zero is not just a place-holder but an indicator of the precision, and therefore a significant figure.
What access indicator?
That access indicator.
What is a bank-and-turn indicator?
A bank-and-turn indicator is an instrument in an aircraft cockpit which incorporates the functions of a bank indicator and a turn indicator.
How many significant figures are in a number 0.0040090?
5 significant figures, from the 4 onwards. This assumes the last zero is not a place holder but an indicator of the degree of accuracy.
What is indicator zero corrector?
23
How many miles do you have after your indicator shows 0 miles?
zero.
How do you reset the srs light on a 2000 Honda civic?
These are the instructions out of the Honda Service Manual for 1996-2000 Civics: 1.) Make sure the ignition switch is OFF. 2.) Connect the SCS service connector to the MES connector. Do not use a jumper wire. 3.) Turn the ignition switch ON. 4.) The SRS indicator light comes on for about six second and goes off. Remove the SCS service connector from the MES connector within 4 seconds after the SRS indicator light went off. 5.) The SRS indicator light comes on again. Reconnect the SCS service connector to the MES connector within 4 seconds after the SRS indicator light comes on. 6.) The SRS indicator light goes off. Remove the SCS service connector from the MES connector within 4 seconds. 7.) The SRS indicator light indicates that the memory is erased by blinking two times. 8.) Turn the ignition swith OFF, and wait for ten seconds. Ok first you're asking what the SCS service connector is. Basically it's a jumper wire. It just has a connector so you can easily connect and disconnect it. You can in fact you a jumper wire. It just might make it a little more difficult. Now you want to know where there MES connector is. It's a yellow 2 wire connector located underneath the dashboard near the fuse panel.
You have a 1997 Honda civic and its srs light keeps turned on you want to know that how can you reset the srs light on?
These are the instructions out of the Honda Service Manual for 1996-2000 Civics:1.) Make sure the ignition switch is OFF.2.) Connect the SCS service connector to the MES connector. Do not use a jumper wire.3.) Turn the ignition switch ON.4.) The SRS indicator light comes on for about six second and goes off. Remove the SCS service connector from the MES connector within 4 seconds after the SRS indicator light went off.5.) The SRS indicator light comes on again. Reconnect the SCS service connector to the MES connector within 4 seconds after the SRS indicator light comes on.6.) The SRS indicator light goes off. Remove the SCS service connector from the MES connector within 4 seconds.7.) The SRS indicator light indicates that the memory is erased by blinking two times.8.) Turn the ignition swith OFF, and wait for ten seconds.Ok first you're asking what the SCS service connector is. Basically it's a jumper wire. It just has a connector so you can easily connect and disconnect it. You can in fact you a jumper wire. It just might make it a little more difficult.Now you want to know where there MES connector is. It's a yellow 2 wire connector located underneath the dashboard near the fuse panel.
How do you remove the side indicator lamps on a Volvo S60?
Begin by removing the side indicator lamp connector. Take hold of the lamp, push in and turn at the same time. The lamp will come out.
How can you have 0 percent of something?
Zero is a number not an idea. If you have no pennies, that means you have zero percent of 100 pennies. If you have one penny, that means you have 1 percent of 100 pennies, or one dollar. Zero like any other number is an indicator of amount. Likewise percentage is also an indicator of an amount of the whole.
How do you replace an indicator bulb on a Skoda?
Begin by removing the connector from the back of your VW drivers side indicator light. You can remove the light bulb by pushing it in and turning at the same time. Reverse the process to install your new drivers side indicator light bulb.
How many significant figure are in 23.70?
4, assuming the last zero is an indicator of precision.
How do you replace a switch -engine coolant level indicator connector on a 2004 Oldsmobile alero?
Purchase a "pig tail" from the dealer and splice it in.
What does a small triangle embedded on a connector signify?
A small triangle on the connector is the indicator for the positive lead. This marks one of the outside wires as pin 1. Line up pin 1 on the connector with the pin 1 found on the motherboard.the wire nearest the triangle is pin 1
How do you reset the SRS light on a 96 Honda Civic Do the same procedures used for 99 and up models work?
i had the same problem on my 97 Honda civic lx. the check engin elight came on adn i called my dealor(aka my best friend) he said just unplug the battery for like 2 min or so and the brain wil restet itself. This is incorrect. Yes the procedure is the same for 1996-2000. See them below: These are the instructions out of the Honda Service Manual for 1996-2000 Civics: 1.) Make sure the ignition switch is OFF. 2.) Connect the SCS service connector to the MES connector. Do not use a jumper wire. 3.) Turn the ignition switch ON. 4.) The SRS indicator light comes on for about six second and goes off. Remove the SCS service connector from the MES connector within 4 seconds after the SRS indicator light went off. 5.) The SRS indicator light comes on again. Reconnect the SCS service connector to the MES connector within 4 seconds after the SRS indicator light comes on. 6.) The SRS indicator light goes off. Remove the SCS service connector from the MES connector within 4 seconds. 7.) The SRS indicator light indicates that the memory is erased by blinking two times. 8.) Turn the ignition swith OFF, and wait for ten seconds. Ok first you're asking what the SCS service connector is. Basically it's a jumper wire. It just has a connector so you can easily connect and disconnect it. You can in fact you a jumper wire. It just might make it a little more difficult. Now you want to know where there MES connector is. It's a yellow 2 wire connector located underneath the dashboard near the fuse panel.
How do you fix a indicator light on a A4avant 2002?
Remove the connector from the back of your indicator light assembly. Take hold of the lightbulb, push in and turn at the same time. The lightbulb will come out. Reverse the process to install your new lightbulb.
