0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What effect if any does connecting an ammeter in series with a resistor in a circuit have on the current through resistor?
The Amp meter was design to allow current flow through the meter to measure with a minimal alteration to the original circuit. That is the ideal world, in reality the meter has some resistance and will lower the current flow. The multiple current setting on most meter will reduce the effects caused by the meter but you must be careful not to damage the meter by reading to high for the setting.
How is an ohmmeter connected to a circuit?
ANY METER needs some kind of current flow to operate. Internal in the meter there are batteries that provide current that when passed trough a resistor will develop voltage as a function of the current. the meter will read this current and display the resistor size to cause this current to flow.
What is the reason of reverse indication on in single phase kWH meter?
A kWh meter measures the flow of energy along the circuit that the meter is connected to. Normally power flows from the supply to the load, which is the conventional direction, but in some cases, for example if the load is replaced by a generator, power can flow the other way and in that case the meter indicates a backward, negative, flow of power.
When there is a break on the circuit what is the reading?
The typical answer is current is zero when there is a break in the circuit. It depends on the complexity of the circuit, there may be other paths for the current to flow, such that if there is a break in one part of the circuit, the rest of the circuit still has current flow (but a different value than designed). If you are reading voltage, and there is a break then that will change, also depending on the complexity. If it is a single loop, and you're reading voltage before the break, your voltmeter will read the same voltage as the voltage source, since there is no current flowing between any resistors between the meter and the source. If you're reading voltage after the break then the meter will read zero (0) volts.
What is closed path throuth which current can flow?
An electric circuit.
Which is better to control a pneumatic cylinder- a meter-in flow control or a meter-out flow control?
When a pneumatic cylinder chamber is filled with pressurized air and the air-chamber on the other side of the piston is metered-out by a flow control, the movement or speed of the cylinder is more consistent than to meter-in the pressurized air.
What is used to measure the intensity of current flow in a circuit or branch in a circuit and is wired in series with the circuit being evaluated?
An Amp Meter
Why do people want switches on mechanisms that use electricity?
To control the flow of current - either to make it flow through the circuit or stop the flow through the circuit
What does a flow meter control?
A flow meter is a device that measures the energy flow of either a liquid or a gas. Like if you have nitrous oxide in a tank and you want to know how much is left after you use some, a flow meter would tell you.
What is the purposed of resistance in the circuit?
Resistance is generally used to control the flow of amount of current in the circuit.
In a circuit the purpose of a switch is to?
In a circuit, the purpose of a switch is to control the current flow to the load by opening the circuit (off) or closing the circuit (on). When the circuit is open, the is no complete loop through which the current can flow. When the switch closes the circuit, it restores the loop, and thus allows the current to flow.
How a fuse controls the flow of electric current in a circuit?
A fuse does not control the flow in a circuit, it limits the current in a circuit. If the load in a circuit shorts out the fuse link melts and opens the circuit and stops the current flow and prevents the wires feeding the circuit from melting and catching fire. resist
How does a switch control the flow of electricity?
When the switch is open, the circuit is not a complete circuit. Electricity needs a complete circuit of conductive material. The switch breaks the circuit causing the flow of electricity to be disrupted. When you close the switch, a full circuit is restored thus restoring the flow of electricity.
What are the devices that control the flow of electricity by breaking or completing a circuit?
a switch
Why are series circuit used for most control circuit?
Because The opening of any switch in a series circuit will open the circuit and stop the flow of current to the load
What effect if any does connecting an ammeter in series with a resistor in a circuit have on the current through the resistor?
The Amp meter was design to allow current flow through the meter to measure with a minimal alteration to the original circuit. That is the ideal world, in reality the meter has some resistance and will lower the current flow. The multiple current setting on most meter will reduce the effects caused by the meter but you must be careful not to damage the meter by reading to high for the setting.
What effect if any does connecting an ammeter in series with a resistor in a circuit have on the current through resistor?
The Amp meter was design to allow current flow through the meter to measure with a minimal alteration to the original circuit. That is the ideal world, in reality the meter has some resistance and will lower the current flow. The multiple current setting on most meter will reduce the effects caused by the meter but you must be careful not to damage the meter by reading to high for the setting.
